GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Saturn 🢒 2004 🢒 VUE - FWD 🢒 Transmission/Transaxle 🢒 Automatic Transmission - VT25-E 🢒 DTC P0962

Object Number: 882392 Size: MF
Master Electrical Component List
Automatic Transmission Controls Schematics
OBD II Symbol Description Notice

Circuit Description

The TCM uses the line pressure control (PC) solenoid valve in order to regulate the transmission line pressure. The line PC solenoid valve is attached to the control solenoid valve assembly. The TCM compares TP angle signal, transmission fluid temperature, speed ratio, and other inputs in order to determine the line pressure appropriate for a given load. The TCM regulates the pressure by applying an amperage to the line PC solenoid valve. The applied amperage varies from 0.1 amps for maximum line pressure to 1.1 amps for minimum line pressure. The TCM then monitors the amperage at the return line.

When the TCM detects a continuous short to ground in the line PC solenoid valve circuit, DTC  P0962 sets. DTC P0962 is a type B DTC.

Conditions for Running the DTC
    • No line PC solenoid DTCs P0960, or P0961.
    • The engine speed is greater than 500 RPM for 5 seconds.

Conditions for Setting the DTC

The TCM detects a continuous short to ground for 1.3 seconds.

Action Taken When the DTC Sets
    • The TCM requests the ECM to illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.
    • The TCM turns the power off to the line PC solenoid valve which results in maximum line pressure.
    • The TCM no longer inhibits shifting to between reverse and drive when moving.
    • The TCM commands maximum pressure to the input clutch.
    • The TCM freezes garage shift transmission adaptive functions.
    • The TCM freezes main line pressure transmission adaptive functions.
    • The ECM records the operating conditions when the Conditions for Setting the DTC are met. The ECM stores this information as Freeze Frame and Failure Records.
    • The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as Failure Records.
    • The TCM stores DTC P0962 in TCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC
    • The ECM turns OFF the MIL after the third consecutive drive trip in which the TCM does not send a MIL illumination request.
    • A scan tool can clear the MIL/DTC.
    • The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring.
    • The TCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the TCM.

Diagnostic Aids
    • Inspect the connectors at the TCM, the transmission, and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections .
    • Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents .

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check - Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls in Engine Controls - 2.2L (L61)

2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.

    3. Important: 

       • Before clearing the DTC, use the scan tool in order to record the Failure Records. Using the Clear DTC Info function erases the Failure Records from the TCM.
       • Using the Clear DTC Info function erases stored DTCs in both the ECM and TCM.

  3. Record the DTC Failure Records.
  4. Clear the DTC.
  5. Turn OFF the ignition for 30 seconds.
  6. Start the engine and idle for 1 minute.
  7. Select Specific DTC.
  8. Enter DTC P0962.

Does the DTC fail this ignition?

--

Go to Step 3

Go to Intermittent Conditions in Engine Controls - 2.2L (L61)

3
  1. Turn OFF the ignition .
  2. Disconnect the AT inline 20-way connector. Additional DTCs may set.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between battery positive and high control circuit of the line PC solenoid valve.

Does the test lamp illuminate?

--

Go to Step 4

Go to Step 5

4

Test the high control circuit of the line PC solenoid valve for a short to ground.

Refer to Testing for Short to Ground and Wiring Repairs in Wiring Repairs.

Did you find and correct a condition?

--

Go to Step 10

Go to Step 9

5

Connect a test lamp between the low control circuit of the line PC solenoid valve and a good ground.

Does the test lamp illuminate?

--

Go to Step 6

Go to Step 7

6

Test the low control circuit of the Line PC Solenoid Valve for a short to voltage. Refer to Testing for a Short to Voltage and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 9

7

Test the high control circuit for a short to the low control circuit of the line PC solenoid valve. Refer to Testing for Continuity and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 8

8

Replace the Line PC Solenoid Valve. The Line PC Solenoid Valve is part of the control solenoid valve assembly. Refer to Control Valve Body Assembly Disassemble .

Did you complete the replacement?

--

Go to Step 10

--

9

Replace the TCM. Refer to Transmission Control Module Replacement .

Did you complete the replacement?

--

Go to Step 10

--

10

Perform the following procedure in order to verify the repair:

  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle within the conditions for running the DTC as specified in the supporting text.
  4. Select Specific DTC.
  5. Enter DTC P0962.

Has the test run and passed?

--

Go to Step 11

Go to Step 2

11

With the scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List in Engine Controls - 2.2L (L61)

System OK