Diagnostic Instructions
Circuit/System Description
The tire pressure monitor receiver receives a radio frequency (RF) transmission from each tire pressure sensor. Each sensor RF transmission contains its own unique identification (ID) code that must be learned into the tire pressure monitor receiver memory.
Once all 4 IDs have been learned and vehicle speed is greater than 32 km/h (20 mph), the tire pressure monitor receiver continuously compares IDs in received transmission to its learned IDs to determine if all 4 sensors are
present. If the tire pressure monitor receiver detects a low tire pressure condition or a malfunction in the system, it will send a serial data message to the instrument panel cluster (IPC) requesting tire pressure monitor indicator illumination.
Diagnostic Aids
| • | Some aftermarket wheel valve stem holes are located further from the wheel rim than original equipment wheels. When using the TPM special tool to activate a sensor, ensure the tool antenna is no further than 15 cm (6 in) from
the sensor and is aiming upward. |
| • | Aftermarket wheel value stem locations can cause a sensor to not function correctly. |
| • | A sensor may have been damaged due to a previous wheel/tire service or flat tire event. |
| • | The use of tire sealants can obstruct the sensor pressure sensing port and cause inaccurate tire pressure readings. If this condition is verified, remove the sealer from the tire and replace the sensor. Refer to
Tire Pressure Indicator Sensor Replacement
. |
| • | Occasionally sensor transmissions are not received by the tire pressure indicator receiver due to vehicle level RF interference from items such as but not limited to aftermarket ignition systems, DVD players, CB radios, or metallic type window tinting. |
| • | Occasionally, stray sensor transmissions can be received from other vehicles. |
Reference Information
Schematic Reference
Tire Pressure Monitoring System Schematics
Description and Operation
Tire Pressure Monitor Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References
for scan tool information
Special Tools
J-46079
Tire Pressure Monitor Diagnostic Tool
Circuit/System Verification
Important: When a TPM DTC is set, the tire pressure monitor indicator icon will flash for 1 minute after the IPC bulb check is completed and then remains illuminated. If equipped with a DIC, a service tire monitor type message
will also be displayed.
Low tire pressure in one or more tires is indicated by a continuously illuminated tire pressure monitor indicator icon after the IPC bulb check is completed. If equipped with a DIC, a check tire pressure type message will
also be displayed.
- Verify all tires are inflated to the proper pressure ± 10%. Refer to
Vehicle Certification, Tire Placard, Anti-Theft, and Service Parts ID Label
.
| ⇒ | If not within the specified range, adjust all tire pressures to specification and drive the vehicle over 32 km/h (20 mph) for greater than 10 minutes. The tire pressure monitor indicator icon should turn OFF. |
- With a scan tool, verify that the TP Sensor Pressure data parameters do not differ more than 27.6 kPa (4 psi) from the actual tire pressure readings.
| ⇒ | If not within the specified range, replace the appropriate tire pressure sensor and perform the Tire Pressure Sensor Learn procedure. |
- Ignition ON, with the scan tool, command the instrument panel cluster (IPC) tire pressure monitor icon OFF. Verify the tire pressure monitor indicator icon turns OFF.
| ⇒ | If the tire pressure monitor icon does not turn OFF, replace the IPC. |
- Perform the Tire Pressure Sensor Learn procedure. With a scan tool, verify that the TP Sensors data parameters display the following:
| • | ID number recorded for each sensor |
| • | Valid ID Status for each sensor |
| • | Accurate tire pressure ± 27.6 kPa (4 psi) for each tire |
| • | Normal Battery status for each sensor |
| ⇒ | If any of the parameters are not as specified, replace the appropriate tire pressure sensor and perform the Tire Pressure Sensor Learn procedure. |
- Perform the Reset ECU and replace the tire pressure indicator receiver.
Repair Instructions
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.
