Callout
| Component Name
|
Preliminary Procedures
- Recover the refrigerant. Refer to
Refrigerant Recovery and Recharging
.
- Remove the air cleaner intake duct from the air cleaner assembly. Refer to
Air Cleaner Inlet Duct Replacement
.
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
- Remove the right front fender liner. Refer to
Front Fender Liner Replacement
.
|
1
| A/C Compressor and Condenser Connector
Tip
- Insert 2 small screwdrivers into the 2 slots of the compressor hose and suction line connector and release locking tabs.
- Remove the A/C compressor hose from the evaporator hose assembly and discard O-rings. Refer to
O-Ring Replacement
.
|
2
| A/C Compressor Hose Clip Bracket Bolt
Notice: Refer to Fastener Notice in the Preface section.
Tighten 10 N·m (89 lb in) |
3
| A/C Compressor Hose Nut
Tip Remove the A/C compressor hose from the A/C compressor and cap hose.
Tighten 20 N·m (15 lb ft) |
4
| Sealing Washer
Tip Remove and discard sealing washers. Refer to
Sealing Washer Replacement
. |
5
| A/C Compressor Hose Bolt
Tighten 20 N·m (15 lb ft) |
6
| Sealing Washer
Tip Remove and discard sealing washers. Refer to
Sealing Washer Replacement
. |
7
| A/C Compressor Hose Assembly
Tip
- Note routing of the A/C compressor hose to ensure proper routing.
- Using
J 39400
leak test A/C compressor hose connections.
|
Callout
| Component Name
|
Preliminary Procedure
- Recover the refrigerant. Refer to
Refrigerant Recovery and Recharging
.
- Remove the air cleaner intake duct fro the air cleaner assembly. Refer to
Air Cleaner Assembly Replacement
.
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
- Remove the right front fender liner. Refer to
Front Fender Liner Replacement
.
|
1
| A/C Compressor and Condenser Connector
Procedure
- Insert 2 small screwdrivers into the 2 slots of the compressor hose and suction line connector and release locking tabs.
- Remove the A/C compressor hose from the evaporator hose assembly and discard O-rings. Refer to
O-Ring Replacement
.
|
2
| A/C Compressor Hose Nut
Notice: Refer to Fastener Notice in the Preface section.
Tip Remove the A/C compressor hose from the A/C compressor and cap hose.
Tighten 20 N·m (15 lb ft) |
3
| Sealing Washer
Tip Remove and discard sealing washers. Refer to
Sealing Washer Replacement
. |
4
| A/C Compressor Hose Bolt
Tighten 20 N·m (15 lb ft) |
5
| Sealing Washer
Tip Remove and discard sealing washers. Refer to
Sealing Washer Replacement
. |
6
| A/C Compressor Hose Assembly
Tip
- Note routing of the A/C compressor hose to ensure proper routing.
- Using
J 39400
leak test A/C compressor hose connections.
Special ToolsJ 39400
Electronic Halogen Leak Detector
|
Callout
| Component Name
|
Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications:
Refer to
Fastener Tightening Specifications .
Preliminary Procedure
- Recover the refrigerant. Refer to
Refrigerant Recovery and Recharging .
- Remove the air cleaner intake duct fro the air cleaner assembly. Refer to
Air Cleaner Assembly Replacement .
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle .
- Remove the right front fender liner. Refer to
Front Fender Liner Replacement .
|
1
| Connector, A/C Compressor and Condenser
Procedure
- Insert 2 small screwdrivers into the 2 slots of the compressor hose and suction line connector and release locking tabs.
- Remove the A/C compressor hose from the evaporator hose assembly and discard O-rings. Refer to
O-Ring Replacement .
|
2
| Nut, A/C Compressor Hose
Tip Remove the A/C compressor hose from the A/C compressor and cap hose.
Tighten 20 N·m (15 lb ft) |
3
| Washer, Sealing
Tip Remove and discard sealing washers. Refer to
Sealing Washer Replacement . |
4
| Bolt, A/C Compressor Hose
Tighten 20 N·m (15 lb ft) |
5
| Washer, Sealing
Tip Remove and discard sealing washers. Refer to
Sealing Washer Replacement . |
6
| Hose Assembly, A/C Compressor
Procedure
- Note routing of the A/C compressor hose to ensure proper routing.
- Using
J 39400 leak test A/C compressor hose connections.
|
Callout
| Component Name
|
Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications:
Refer to
Fastener Tightening Specifications
.
Preliminary Procedure
- Recover the refrigerant. Refer to
Refrigerant Recovery and Recharging
.
- Remove the air cleaner intake duct from the air cleaner assembly. Refer to
Air Cleaner Assembly Replacement
.
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
- Remove the right front fender liner. Refer to
Front Fender Liner Replacement
.
|
1
| Connector, A/C Compressor and Condenser
Procedure
- Insert 2 small screwdrivers into the 2 slots of the compressor hose and suction line connector and release locking tabs.
- Remove the A/C compressor hose from the evaporator hose assembly and discard O-rings. Refer to
O-Ring Replacement
.
|
2
| Nut, A/C Compressor Hose
Tip Remove the A/C compressor hose from the A/C compressor and cap hose.
Tighten 20 N·m (15 lb ft) |
3
| Washer, Sealing
Tip Remove and discard sealing washers. Refer to
Sealing Washer Replacement
. |
4
| Bolt, A/C Compressor Hose
Tighten 20 N·m (15 lb ft) |
5
| Washer, Sealing
Tip Remove and discard sealing washers. Refer to
Sealing Washer Replacement
. |
6
| Hose Assembly, A/C Compressor
Procedure
- Note routing of the A/C compressor hose to ensure proper routing.
- Using
J 39400
leak test A/C compressor hose connections.
|