GM Service Manual Online
For 1990-2009 cars only

Brake Pressure Modulator Valve Replacement w/o JL4


Object Number: 1772702  Size: MF

Callout

Component Name

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.

Notice: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.

Preliminary Procedures

  1. Turn the ignition switch to the OFF position.
  2. Reposition the air cleaner outlet resonator forward slightly. Lift to release the resonator from the studs on the rail. Refer to Air Cleaner Outlet Resonator Replacement .
  3. Clean the electronic brake control module (EBCM) to brake pressure modulator valve (BPMV) area of any accumulated dirt and foreign material.

1

Electronic Brake Control Module (EBCM) Electrical Connector

Procedure

Lift the EBCM electrical connector locking lever upward.

2

Brake Pipe Fitting (Qty: 6)

Notice: Refer to Fastener Notice in the Preface section.

Procedure

  1. Note the location of the brake pipe fittings for installation.
  2. Cap the brake pipe fittings to prevent brake fluid loss and contamination.
  3. Carefully position the brake pipes aside to provide access to remove the BPMV assembly.

Tighten
20 N·m (15 lb ft)

3

Brake Pressure Modulator Valve (BPMV) Bracket Bolt (Qty: 2)

Tighten
10 N·m (89 lb in)

4

BPMV Bracket Bolt

Tip
Loosen but do not remove the bolt.

Tighten
10 N·m (89 lb in)

5

BPMV Assembly

Procedure

  1. Plug the BPMV inlet and outlet ports to prevent brake fluid loss and contamination.
  2. Remove the BPMV to bracket mounting bolt.
  3. Do not pry against the accumulator covers on the underside of the brake pressure modulator assembly to release the mounting pins from the bracket insulators.
  4. Do not remove the mounting pins unless it is necessary to aid in releasing the modulator assembly from the bracket.
  5. Inspect the insulators and replace if necessary.
  6. If installing a new BPMV, remove the EBCM. Refer to Electronic Brake Control Module Replacement .
  7. A new BPMV comes with both the primary and secondary circuits pre-filled with brake fluid. As long as the ignition key has not been cycled after installation, only a base brake bleed is necessary. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding .
  8. Perform the Diagnostic System Check - Vehicle .
  9. Observe brake pedal feel after performing the diagnostic system check. If the pedal now feels spongy, air may have been in, or may have been introduced into the secondary hydraulic circuit of the brake modulator which then may have been introduced into the primary circuit. If the pedal feels spongy, perform the Antilock Brake System Automated Bleed Procedure .

Tighten
11 N·m (97 lb in)

Removal Procedure

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.

Notice: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.

  1. Turn the ignition switch to the OFF position.
  2. Clean the electronic brake control module (EBCM) to brake pressure modulator valve (BPMV) area of any accumulated dirt and foreign material.

  3. Object Number: 1859458  Size: SH
  4. Disconnect the brake fluid level indicator switch electrical connector.
  5. Disconnect the vacuum brake booster vacuum sensor electrical connector.

  6. Object Number: 1859462  Size: SH
  7. Release the wiring harness retainer from the master cylinder mounting stud and position the wiring harness downward.
  8. Remove and discard the 2 master cylinder nuts.
  9. If equipped, disconnect the clutch master cylinder hose from the brake master cylinder reservoir.
  10. Cap the brake fluid reservoir outlet and plug the clutch master cylinder hose inlet to prevent brake fluid loss and contamination.


    Object Number: 1859463  Size: SH
  11. Remove the 2 master cylinder brake pipe fittings from the BPMV.
  12. Cap the brake pipe fittings and plug the BPMV inlet ports to prevent brake fluid loss and contamination.

  13. Remove the brake master cylinder and master cylinder brake pipes as an assembly.

  14. Object Number: 1859741  Size: SH
  15. Remove the 2 rear brake pipe fittings (1) from the BPMV.
  16. Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  17. Remove the 2 front brake pipe fittings (2) from the BPMV.
  18. Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  19. Lift the locking tabs on the lower edge of the EBCM electrical connector (3) and disconnect the electrical connector.
  20. Position the EBCM electrical connector and the wiring harness toward the front of the vehicle.

  21. Object Number: 1859743  Size: SH
  22. Remove the 2 upper BPMV bracket bolts (1).
  23. Loosen, but do not remove the lower BPMV bracket bolt (2).
  24. Remove the brake modulator and bracket assembly (3).

  25. Object Number: 1859744  Size: SH
  26. Remove the BPMV bolt.
  27. Carefully separate the BPMV from the bracket. Do not pry against the accumulator covers on the underside of the BPMV.

  28. Object Number: 1859745  Size: SH
  29. Remove the EBCM bolts (1).
  30. Carefully pull the EBCM (2) from the BPMV (3). Do not pry the components apart.
  31. If installing a new BPMV, remove and discard the EBCM O-ring seals (4).
  32. If reinstalling the BPMV, clean the sealing surface of the BPMV with denatured alcohol and allow to dry.

Installation Procedure


    Object Number: 1859745  Size: SH
  1. If installing a new BPMV, install new EBCM O-ring seals (4) to the BPMV (3).
  2. Important: Ensure the brake pressure switch is properly aligned to the BPMV when installing the EBCM. Do not force the components together.

  3. Carefully install the EBCM (2) to the BPMV.
  4. Notice: Refer to Fastener Notice in the Preface section.

  5. Install the EBCM bolts (1).
  6. Tighten
    Tighten the bolts to 2.3 N·m (20 lb in).


    Object Number: 1859744  Size: SH
  7. Inspect the BPMV bracket insulators for damage and replace if necessary.
  8. Important: If necessary, a small amount of denatured alcohol can be used as an assembly aid for installing the BPMV mounting pins to the BPMV bracket.

  9. Install the BPMV to the bracket.
  10. Install the BPMV bolt.
  11. Tighten
    Tighten the bolt to 11 N·m (97 lb in).


    Object Number: 1859743  Size: SH
  12. Install the brake modulator and bracket assembly (3). Align the BPMV bracket to the lower bracket bolt (2).
  13. Install the 2 upper brake modulator bracket bolts (1).
  14. Tighten
    Tighten the bolts to 10 N·m (89 lb in).

  15. Install the lower brake modulator bracket bolt.
  16. Tighten
    Tighten the bolt to 10 N·m (89 lb in).


    Object Number: 1859741  Size: SH
  17. Install the 2 rear brake pipe fittings (1) to the BPMV.
  18. Tighten
    Tighten the fittings to 20 N·m (15 lb ft).

  19. Install the 2 front brake pipe fittings (2) to the BPMV.
  20. Tighten
    Tighten the fittings to 20 N·m (15 lb ft).

  21. Connect the EBCM electrical connector (3). Ensure the tabs on the cam lever are securely locked in place.

  22. Object Number: 1859463  Size: SH
  23. Install the brake master cylinder and brake pipes assembly to the vacuum brake booster.
  24. Install the 2 master cylinder brake pipe fittings to the BPMV.
  25. Tighten
    Tighten the fittings to 20 N·m (15 lb ft).


    Object Number: 1859462  Size: SH
  26. If equipped, connect the clutch master cylinder hose to the brake master cylinder reservoir.
  27. Install 2 new brake master cylinder nuts.
  28. Tighten
    Tighten the nuts to 20 N·m (15 lb ft).

  29. Position the wiring harness upward and install the wiring harness retainer to the master cylinder mounting stud on the vacuum brake booster.

  30. Object Number: 1859458  Size: SH
  31. Connect the brake booster vacuum sensor electrical connector.
  32. Connect the brake fluid level indicator switch electrical connector.
  33. If a new EBCM was installed, program the EBCM. Refer to Control Module References.
  34. Important: A new BPMV comes with both the primary and secondary circuits pre-filled with brake fluid. If the ignition key has not been cycled after installation, only a base brake bleed is necessary.

  35. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding.
  36. Perform the Diagnostic System Check - Vehicle.
  37. Observe the brake pedal feel after performing the diagnostic system check. If the pedal now feels spongy, air may have been introduced into the secondary hydraulic circuit of the brake modulator which then may have been introduced into the primary circuit. If the pedal feels spongy, perform the Antilock Brake System Automated Bleed Procedure.

Brake Pressure Modulator Valve Replacement w/JL4

Removal Procedure

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.

Notice: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.

  1. Turn the ignition switch to the OFF position.
  2. Clean the electronic brake control module (EBCM) to brake pressure modulator valve (BPMV) area of any accumulated dirt and foreign material.

  3. Object Number: 1859458  Size: SH
  4. Disconnect the brake fluid level indicator switch electrical connector.
  5. Disconnect the vacuum brake booster vacuum sensor electrical connector.

  6. Object Number: 1859462  Size: SH
  7. Release the wiring harness retainer from the master cylinder mounting stud and position the wiring harness downward.
  8. Remove and discard the 2 master cylinder nuts.
  9. If equipped, disconnect the clutch master cylinder hose from the brake master cylinder reservoir.
  10. Cap the brake fluid reservoir outlet and plug the clutch master cylinder hose inlet to prevent brake fluid loss and contamination.


    Object Number: 1859463  Size: SH
  11. Remove the 2 master cylinder brake pipe fittings from the BPMV.
  12. Cap the brake pipe fittings and plug the BPMV inlet ports to prevent brake fluid loss and contamination.

  13. Remove the brake master cylinder and master cylinder brake pipes as an assembly.

  14. Object Number: 1859741  Size: SH
  15. Remove the 2 rear brake pipe fittings (1) from the BPMV.
  16. Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  17. Remove the 2 front brake pipe fittings (2) from the BPMV.
  18. Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  19. Lift the locking tabs on the lower edge of the EBCM electrical connector (3) and disconnect the electrical connector.
  20. Position the EBCM electrical connector and the wiring harness toward the front of the vehicle.

  21. Object Number: 1859743  Size: SH
  22. Remove the 2 upper BPMV bracket bolts (1).
  23. Loosen, but do not remove the lower BPMV bracket bolt (2).
  24. Remove the brake modulator and bracket assembly (3).

  25. Object Number: 1859744  Size: SH
  26. Remove the BPMV bolt.
  27. Carefully separate the BPMV from the bracket. Do not pry against the accumulator covers on the underside of the BPMV.

  28. Object Number: 1859745  Size: SH
  29. Remove the EBCM bolts (1).
  30. Carefully pull the EBCM (2) from the BPMV (3). Do not pry the components apart.
  31. If installing a new BPMV, remove and discard the EBCM O-ring seals (4).
  32. If reinstalling the BPMV, clean the sealing surface of the BPMV with denatured alcohol and allow to dry.

Installation Procedure


    Object Number: 1859745  Size: SH
  1. If installing a new BPMV, install new EBCM O-ring seals (4) to the BPMV (3).
  2. Important: Ensure the brake pressure switch is properly aligned to the BPMV when installing the EBCM. Do not force the components together.

  3. Carefully install the EBCM (2) to the BPMV.
  4. Notice: Refer to Fastener Notice in the Preface section.

  5. Install the EBCM bolts (1).
  6. Tighten
    Tighten the bolts to 2.3 N·m (20 lb in).


    Object Number: 1859744  Size: SH
  7. Inspect the BPMV bracket insulators for damage and replace if necessary.
  8. Important: If necessary, a small amount of denatured alcohol can be used as an assembly aid for installing the BPMV mounting pins to the BPMV bracket.

  9. Install the BPMV to the bracket.
  10. Install the BPMV bolt.
  11. Tighten
    Tighten the bolt to 11 N·m (97 lb in).


    Object Number: 1859743  Size: SH
  12. Install the brake modulator and bracket assembly (3). Align the BPMV bracket to the lower bracket bolt (2).
  13. Install the 2 upper brake modulator bracket bolts (1).
  14. Tighten
    Tighten the bolts to 10 N·m (89 lb in).

  15. Install the lower brake modulator bracket bolt.
  16. Tighten
    Tighten the bolt to 10 N·m (89 lb in).


    Object Number: 1859741  Size: SH
  17. Install the 2 rear brake pipe fittings (1) to the BPMV.
  18. Tighten
    Tighten the fittings to 20 N·m (15 lb ft).

  19. Install the 2 front brake pipe fittings (2) to the BPMV.
  20. Tighten
    Tighten the fittings to 20 N·m (15 lb ft).

  21. Connect the EBCM electrical connector (3). Ensure the tabs on the cam lever are securely locked in place.

  22. Object Number: 1859463  Size: SH
  23. Install the brake master cylinder and brake pipes assembly to the vacuum brake booster.
  24. Install the 2 master cylinder brake pipe fittings to the BPMV.
  25. Tighten
    Tighten the fittings to 20 N·m (15 lb ft).


    Object Number: 1859462  Size: SH
  26. If equipped, connect the clutch master cylinder hose to the brake master cylinder reservoir.
  27. Install 2 new brake master cylinder nuts.
  28. Tighten
    Tighten the nuts to 20 N·m (15 lb ft).

  29. Position the wiring harness upward and install the wiring harness retainer to the master cylinder mounting stud on the vacuum brake booster.

  30. Object Number: 1859458  Size: SH
  31. Connect the brake booster vacuum sensor electrical connector.
  32. Connect the brake fluid level indicator switch electrical connector.
  33. If a new EBCM was installed, program the EBCM. Refer to Electronic Brake Control Module Programming and Setup.
  34. Important: A new BPMV comes with both the primary and secondary circuits pre-filled with brake fluid. If the ignition key has not been cycled after installation, only a base brake bleed is necessary.

  35. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding.
  36. Perform the Diagnostic System Check - Vehicle.
  37. Observe the brake pedal feel after performing the diagnostic system check. If the pedal now feels spongy, air may have been introduced into the secondary hydraulic circuit of the brake modulator which then may have been introduced into the primary circuit. If the pedal feels spongy, perform the Antilock Brake System Automated Bleed Procedure.