Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0563: System Voltage HighDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Ignition 1 Signal | -- | -- | P0563 | -- |
Circuit/System Description
The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range.
Conditions for Running the DTC
| • | The vehicle speed is above 8 km/h (5 mph). |
| • | The system voltage is between 9.5-18 volts. |
Conditions for Setting the DTC
The ECM detects a system voltage above 16 volts for less than 1 second.
Action Taken When the DTC Sets
| • | The ECM will command the charge indicator and or warning message to be illuminated on the instrument panel cluster (IPC) and the driver information center (DIC), if equipped. |
| • | The ECM will not illuminate the malfunction indicator lamp (MIL). |
| • | The ECM will store conditions, which were present when the DTC set as Failure Records data only. |
Conditions for Clearing the DTC
| • | The ECM will command the message OFF after one trip in which the diagnostic test has been run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | Using the scan tool Clear DTC Information function can clear the DTC. |
Reference Information
Schematic Reference
Starting and Charging Schematics
Connector End View Reference
Engine Electrical Connector End Views
Electrical Information Reference
Scan Tool Reference
Circuit/System Verification
- If the DTC is history, refer to Charging System Test
- Start the engine, record the voltage at the battery terminals. Observe the Ignition 1 signal parameter in the ECM data list. Voltages should not differ by more than 1 volt.
| ⇒ | If more than 1 volt, replace the ECM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for ECM replacement, setup, and programming
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0563 : System Voltage HighCircuit/System Description
The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range.
Conditions for Running the DTC
| • | The vehicle speed is above 8 km/h (5 mph). |
| • | The system voltage is between 9.5-18 volts. |
Conditions for Setting the DTC
The ECM detects a system voltage above 16 volts for less than 1 second.
Action Taken When the DTC Sets
| • | The ECM will command the charge indicator and or warning message to be illuminated on the instrument panel cluster (IPC) and the driver information center (DIC), if equipped. |
| • | The ECM will not illuminate the malfunction indicator lamp (MIL). |
| • | The ECM will store conditions, which were present when the DTC set as Fail Records data only. |
Conditions for Clearing the DTC
| • | The ECM will command the message OFF after one trip in which the diagnostic test has been run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
Reference Information
Schematic Reference
Starting and Charging Schematics
Connector End View Reference
Engine Electrical Connector End Views
Description and Operation
Charging System Description and Operation
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Circuit/System Verification
Ignition ON and the engine OFF, observe the ECM Ignition 1 Signal parameter. The Ignition 1 Signal parameter should read 16 volts or less.
Circuit/System Testing
- Measure the voltage at the battery terminals and compare it with the ECM Ignition 1 Signal parameter. Verify that battery and ignition 1 signal readings do not differ more than 0.5 volt.
- Go to Charging System Test .
| ⇒ | If greater than 0.5 volt, test the ignition 1 ground circuits of the ECM for high resistance or replace the ECM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for ECM replacement, setup, and programming.
