DTC P0532 or P0533. Pontiac Pursuit 2006

For 1990-2009 cars only

Makes 🢒 Pontiac 🢒 2006 🢒 Pursuit 🢒 DTC 🢒 DTC P0532 or P0533

Circuit Description

The engine control module (ECM) or powertrain control module (PCM) monitors the high side refrigerant pressure through the A/C refrigerant pressure sensor. The ECM or PCM supplies a 5-volt reference and a low reference to the sensor. Changes in the A/C refrigerant pressure cause the A/C refrigerant pressure sensor signal to the ECM or PCM to vary. When the pressure is high, the signal voltage is high. When the pressure is low, the signal voltage is low. When pressure is high, the ECM or PCM commands the cooling fans ON. When pressure is too high or too low, the ECM or PCM will not allow the A/C compressor clutch to engage.

DTC Descriptors

This diagnostic procedure supports the following DTCs:

•	DTC P0532 (A/C) Air Conditioning Pressure Sensor Circuit Low Voltage

•	DTC P0533 (A/C) Air Conditioning Pressure Sensor Circuit High Voltage

Conditions for Running the DTC

•	The engine is running.

•	Any of the conditions for setting the DTC are met for 15 seconds.

Conditions for Setting the DTC

•	The ECM or PCM detects that the A/C pressure is less than 34 Kpa or 4.93 psi (0.25 volt).

•	The ECM or PCM detects that the A/C pressure is more than 3339 Kpa or 484 psi (4.75 volts).

Action Taken When the DTC Sets

•	The ECM or PCM will not illuminate the malfunction indicator lamp (MIL).

•	The ECM or PCM stores the Failure Records.

•	The A/C compressor clutch is disabled.

Conditions for Clearing the DTC

•	The history DTC will clear after 40 consecutive ignition cycles have occurred without a malfunction.

•	The DTC can be cleared by using the scan tool.

•	The DTC will become history if the ECM or PCM no longer detects a failure.

Diagnostic Aids

Test the following conditions:

•	Visually inspect the sensor for contamination or damage.

•	Inspect for the following that may affect the sensors accuracy:

-	A malfunction within the refrigerant system causing high pressure

-	Visually inspect the A/C components and lines for damage.

•	Refer to Testing for Intermittent Conditions and Poor Connections .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step tests for the proper operation of the circuit in the low voltage range.

This step tests for the proper operation of the circuit in the high voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to ground.

This step tests for a short to voltage in the 5-volt reference circuit.

This step tests for a high resistance or an open in the low reference circuit.

Step	Action	Values	Yes	No
Schematic Reference: HVAC Schematics Connector End View Reference: HVAC Connector End Views
1	Did you perform the Diagnostic System Check - Vehicle?	--	Go to Step 2	Go to Diagnostic System Check - Vehicle
2	Important: The ambient air temperature must be above 3°C (38°F). Turn OFF the ignition. Inspect the A/C compressor for free rotation operation. Start the engine. Place the HVAC control assembly in the OFF position. Does the A/C compressor operate?	--	Go to Air Conditioning Compressor Malfunction	Go to Step 3
3	Install a scan tool. Turn ON the ignition, with the engine OFF. With a scan tool, observe the A/C Refrigerant Pressure parameter in the engine control module (ECM) or powertrain control module (PCM) General Info Inputs/Outputs data list. Does the scan tool indicate that the A/C refrigerant pressure parameter is within the specified range?	0.25-4.75 V	Go to Diagnostic Aids	Go to Step 4
4	Turn OFF the ignition. Disconnect the A/C refrigerant pressure sensor. Turn ON the ignition, with the engine OFF. With a scan tool, observe the A/C Refrigerant Pressure parameter in the ECM or PCM General Info Inputs/Outputs data list. Does the scan tool indicate that the A/C Refrigerant Pressure parameter is less than the specified value?	0.25 V	Go to Step 5	Go to Step 11
5	Turn OFF the ignition. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the A/C refrigerant pressure sensor and the signal circuit of the A/C refrigerant pressure sensor. Turn ON the ignition, with the engine OFF. With a scan tool, observe the A/C Refrigerant Pressure parameter in the ECM or PCM General Info Inputs/Outputs data list. Does the scan tool indicate that the A/C Refrigerant pressure parameter is greater than the specified value?	4.75 V	Go to Step 6	Go to Step 9
6	Disconnect the fused jumper wire. Measure the voltage between the 5-volt reference circuit of the A/C refrigerant pressure sensor and the low reference circuit of the A/C refrigerant pressure sensor. Does the voltage measure less than the specified value?	4.75 V	Go to Step 7	Go to Step 8
7	Turn OFF the ignition. Disconnect the negative battery cable. Measure the resistance from the low reference circuit of the A/C refrigerant pressure sensor to a good ground. Does the resistance measure less than the specified value?	5 ohms	Go to Step 13	Go to Step 12
8	Test the 5-volt reference circuit of the A/C refrigerant pressure sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	--	Go to Step 17	Go to Step 14
9	Test the 5-volt reference circuit of the A/C refrigerant pressure sensor for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	--	Go to Step 17	Go to Step 10
10	Test the signal circuit of the A/C refrigerant pressure sensor for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	--	Go to Step 17	Go to Step 14
11	Test the signal circuit of the A/C refrigerant pressure sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	--	Go to Step 17	Go to Step 14
12	Disconnect the ECM or PCM. Test the low reference circuit of the A/C refrigerant pressure sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition?	--	Go to Step 17	Go to Step 14
13	Inspect for poor connections at the harness connector of the A/C refrigerant pressure sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition?	--	Go to Step 17	Go to Step 15
14	Inspect for poor connections at the harness connector of the ECM or PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition?	--	Go to Step 17	Go to Step 16
15	Replace the A/C refrigerant pressure sensor. Refer to Air Conditioning (A/C) Refrigerant Pressure Sensor Replacement . Did you complete the replacement?	--	Go to Step 17	--
16	Replace the ECM or PCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement?	--	Go to Step 17	--
17	Use the scan tool in order to clear the DTCs. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text. Does the DTC reset?	--	Go to Step 2	System OK