GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2006 🢒 Pursuit 🢒 Engine 🢒 Engine Electrical 🢒 Battery Positive Cable Replacement

Battery Positive Cable Replacement Underhood Junction Block to Starter

Removal Procedure

Important: 

   • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
   • Always route the replacement cable the same way as the original cable.


    Object Number: 1656241 Size: SH
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Remove the junction block cover.
  3. Remove the junction block nut (1).
  4. Remove the positive battery cable terminal (2) from the junction block stud.
  5. Remove the positive battery cable clip (3) from the engine control module (ECM) bracket.
  6. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.

    7. Object Number: 1656131 Size: SH
  7. Remove the starter solenoid terminal nut (5).
  8. Remove the positive battery cable terminal (4) from the starter solenoid.

    9. Object Number: 1656337 Size: SH
  9. Cut open the tape on the positive/negative battery cable conduit (1).
  10. Remove the old tape from the conduit.

    11. Object Number: 1656338 Size: SH
  11. Remove the positive battery cable (1).

Installation Procedure

    Object Number: 1656338 Size: SH
  1. Install the positive battery cable (1) to the conduit.

    2. Object Number: 1656337 Size: SH
  2. Wrap tape around the positive/negative battery cable conduit (1).

    3. Object Number: 1647984 Size: SH
  3. Install the positive battery cable terminal (3) to the starter solenoid.

    4. Notice: Refer to Fastener Notice in the Preface section.

  4. Install the starter solenoid terminal nut (4).

    5. Tighten
    Tighten the nut to 17 N·m (13 lb ft).

  5. Lower the vehicle.

    6. Object Number: 1656241 Size: SH
  6. Install the positive battery cable terminal (2) to the junction block stud.
  7. Install the junction block nut (1).

    8. Tighten
    Tighten the nut to 17 N·m (13 lb ft).

  8. Install the positive battery cable clip (3) to the ECM bracket.
  9. Install the junction block cover.
  10. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.

Battery Positive Cable Replacement Battery to Underhood Junction Block

Removal Procedure

Important: 

   • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
   • Always route the replacement cable the same way as the original cable.


    Object Number: 1656237 Size: SH
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the carpet. Refer to Floor Panel Carpet Replacement .
  3. Open the positive battery cable (1) cover.
  4. Loosen the positive battery cable bolt.
  5. Remove the positive battery cable from the battery.
  6. Disconnect the positive battery cable electrical connector (9) from the body harness electrical connector (8).

    7. Object Number: 1548552 Size: SH
  7. From inside the vehicle, remove the positive battery cable clips (1) from the weld studs.
  8. Remove the positive battery cable clip (2) from the floor pan.

    9. Object Number: 1656242 Size: SH
  9. Remove the positive battery cable clip (2) from the latch bar.
  10. Remove the positive battery cable from the body clip (3). Unfold the tabs in order to remove the cable.
  11. Remove the positive battery cable clips (3) from the weld studs.
  12. Remove the positive battery cable clip (4) from the floor pan.

    13. Object Number: 1650320 Size: SH
  13. Remove the positive battery cable from the body wiring harness clips (1).

    14. Object Number: 1656243 Size: SH
  14. Remove the positive battery cable clip (2) from the weld stud.
  15. Remove the positive battery cable from the body wiring harness clips (3).
  16. Unseat the grommet (1) from the front of dash.

    17. Object Number: 1656241 Size: SH
  17. From under the hood, remove the junction block cover.
  18. Remove the junction block nut (1).
  19. Remove the positive battery cable (to starter) terminal (2) from the stud.

    20. Object Number: 1656244 Size: SH
  20. Remove the positive battery cable (3) from the body wiring harness clip (2).
  21. Remove the positive battery cable clip (1) from the junction block.
  22. Remove the positive battery cable from under the junction block.
  23. Route the positive battery cable through the hole in the front of dash.
  24. From inside the vehicle, remove the positive battery cable.

Installation Procedure

    Object Number: 1656244 Size: SH
  1. From inside the vehicle, layout the positive battery cable assembly.
  2. Route the positive battery cable through the hole in the front of dash.
  3. From under the hood, route the positive battery cable under the junction block.
  4. Install the positive battery cable clip (1) to the junction block.
  5. Install the positive battery cable (3) from the body wiring harness clip (2).

    6. Object Number: 1656241 Size: SH
  6. Install the positive battery cable (to starter) terminal (2) to the stud.

    7. Notice: Refer to Fastener Notice in the Preface section.

  7. Install the junction block nut (1).

    8. Tighten
    Tighten the nut to 17 N·m (13 lb ft).

  8. Install the junction block cover.

    9. Object Number: 1656243 Size: SH
  9. From inside the vehicle, seat the grommet (1) to the front of dash.
  10. Install the positive battery cable to the body wiring harness clips (3).
  11. Install the positive battery cable clip (2) to the weld stud.

    12. Object Number: 1650320 Size: SH
  12. Install the positive battery cable to the body wiring harness clips (1).

    13. Object Number: 1656242 Size: SH
  13. Install the positive battery cable clip (4) to the floor pan.
  14. Install the positive battery cable clips (3) to the weld studs.
  15. Install the positive battery cable to the body clip (3).
  16. Install the positive battery cable clip (2) to the latch bar.

    17. Object Number: 1548552 Size: SH
  17. Install the positive battery cable clip (2) to the floor pan.
  18. Install the positive battery cable clips (1) to the weld studs.

    19. Object Number: 1656237 Size: SH
  19. Connect the positive battery cable electrical connector (9) to the body harness electrical connector (8).
  20. Install the positive battery cable to the battery.
  21. Tighten the positive battery cable bolt.

    22. Tighten
    Tighten the bolt to 17 N·m (13 lb ft).

  22. Close the positive battery cable (1) cover.
  23. Install the carpet. Refer to Floor Panel Carpet Replacement .
  24. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .