Schematic Reference: Moveable Window Schematics

Connector End View Reference: Window Systems Connector End Views

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

Verify that the inoperative passenger door power window fault is present.

Do the passenger door power windows operate normally?

Go to Testing for Intermittent Conditions and Poor Connections

Go to Step 3

Is the inoperative window the front passenger window?

Go to Step 5

Go to Step 4

Are the driver, LR and RR windows all inoperative?

Go to Step 9

Go to Step 6

1. Disconnect the harness connector of the front passenger window switch.
2. Turn ON the ignition, with the engine OFF.
3. Probe the accessory voltage circuit of the harness connector with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 7

Go to Step 16

1. Disconnect the appropriate window switch.
2. Turn ON the ignition, with the engine OFF.
3. Probe the power window master switch lockout signal circuit of the appropriate window switch with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 7

Go to Step 10

1. Connect a test lamp between the power window master switch up signal circuit of the appropriate window switch and the power window master switch down signal circuit of the appropriate window switch.
2. Operate the driver window switch to the UP and DOWN positions.

Does the test lamp illuminate in both positions?

Go to Step 8

Go to Step 11

1. Connect the appropriate window switch.
2. Disconnect the appropriate window motor.
3. Connect a test lamp between the power window motor up circuit of the appropriate window motor and the power window motor down circuit of the appropriate window motor.
4. Operate the appropriate window switch to the UP and DOWN positions.

Does the test lamp illuminate in both positions?

Go to Step 14

Go to Step 12

Test the accessory voltage circuit of the driver window switch for an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 20

Go to Step 13

Test the power window master switch lockout signal circuit of the appropriate window switch for an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 20

Go to Step 13

Test the power window master switch signal circuits of the appropriate window switch for a short to ground or an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 20

Go to Step 13

Test the appropriate window motor up and down circuits of the appropriate window motor for a short to ground or an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 20

Go to Step 15

Inspect for poor connections at the harness connector of the driver window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 20

Go to Step 17

Inspect for poor connections at the harness connector of the appropriate window motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs .

Did you find and correct the condition?

Go to Step 20

Go to Step 18

Inspect for poor connections at the harness connector of the appropriate window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 20

Go to Step 19

Repair the open in the accessory voltage circuit.

Did you complete the repair?

Go to Step 20

--

Replace the driver window switch.

Did you complete the replacement?

Go to Step 20

--

Replace the appropriate window motor. Refer to Front Side Door Window Regulator Replacement or to Rear Side Door Window Regulator Replacement .

Did you complete the replacement?

Go to Step 20

--

Replace the appropriate window switch. Refer to Rear Side Door Window Switch Replacement .

Did you complete the replacement?

Go to Step 20

--

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 2