Circuit Description
The door unlock control circuit from the body control module (BCM) controls the door unlock relay. When the BCM receives a door unlock signal, the BCM supplies battery positive voltage to the relay.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
| • | DTC B3132 All Door Unlock Circuit Low |
| • | DTC B3133 All Door Unlock Circuit High |
Conditions for Running the DTC
The keyfob unlock button is pressed, twice if personalization is configured, or a door lock switch is pressed to the unlock position for DTC B3132. The battery positive voltage supplied to the BCM is within normal operating range, 9 to 16 volts, for DTC B3133.
Conditions for Setting the DTC
The door unlock control circuit is shorted to ground for 0.2 seconds, for DTC B3132. The door unlock control circuit is open or shorted to battery positive voltage for 0.2 seconds, for DTC B3133.
Action Taken When the DTC Sets
The BCM disables the door unlock output for the remainder of the ignition cycle.
Conditions for Clearing the DTC
| • | A current DTC B3132 or DTC B3133 clears when the malfunction is no longer present and the ignition switch is cycled. |
| • | All BCM history codes clear after 100 ignition cycles with no current codes active during the 100 ignition cycles. |
Diagnostic Aids
If the DTC is a history DTC, the problem may be intermittent. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Listen for an audible click when the door unlock relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
-
Verifies that the body control module is providing voltage to the door unlock relay.
-
Tests for an open in the ground circuit to the door unlock relay.
-
Tests if voltage is constantly being applied to the door unlock relay.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Door Lock/Indicator Schematics Connector End View Reference: Power Door Systems Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
Does the door unlock relay turn ON and OFF with each command? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | |
Does the test lamp turn ON and OFF with each command? | Go to Step 4 | Go to Step 5 | |
Does the test lamp turn ON and OFF with each command? | Go to Step 8 | Go to Step 10 | |
Does the test lamp remain illuminated with each command? | Go to Step 7 | Go to Step 6 | |
6 | Test the door unlock control circuit of the door unlock relay for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 9 |
7 | Test the door unlock control circuit of the door unlock relay for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 9 |
8 | Inspect for poor connections at the door unlock relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 11 |
9 | Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 12 |
10 | Repair the open in the ground circuit of the door unlock relay. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 13 | -- |
11 | Replace the door unlock relay. Did you complete the replacement? | Go to Step 13 | -- |
12 | Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 13 | -- |
13 |
Does the DTC reset? | Go to Step 2 | System OK |
