Programming Features
Entering Personalization Mode
Personalization Mode is accessed via the Options Menu, which can be displayed when the vehicle is stationary or moving slowly.
| • | If the vehicle is stationary, turn the ignition key on while pressing the MODE button on the trip computer switch. If the MODE button is pressed a 2nd time, the Options Menu disappears and the display reverts back to the previous trip computer function. |
| • | If the vehicle has been started, the System Check completed and the vehicle speed is less than approximately 10 km/h (6 mph), then the Options Menu is displayed for 3 seconds. If the vehicle is driven at more than approximately 10 km/h (6 mph), the Options Menu disappears and the display reverts back to the previous trip computer function. |
With the Options Menu displayed, press the trip computer UP or DOWN button to enter personalization Mode.
When the personalization Mode is entered, the display shows the Help screens. Press the MODE button to advance to the next Help screen and then again to advance to the Restore to Factory Settings screen.
If the message is too big for one screen a 2nd (or 3rd) screen with more information appears once the MODE button is pressed, until the menu item is shown.
In the Options Menu there are no fixed icons displayed around the outside of the main dot matrix area. If an icon is activated while in the Options Menu, that icon is displayed for 2 seconds and then disappears. Once the Options Menu is exited or the vehicle speed is greater than approximately 10 km/h (6 mph) when the Options Menu is locked out, the icons reappear.
Restore to Factory Settings
The Restore to Factory Settings screen is the first item on the Options Menu. This function restores the instrument cluster, the entertainment system and the body control module to the factory default settings.
Use the trip computer switch UP or DOWN button to select Yes or No. Press the MODE button to continue. If Yes is selected as the option, a 2 second delay allows the default parameters to be updated before the next screen is displayed:
If no selection is made at the Restore to Factory Settings screen within 5 seconds, the Help screen message appears.
Underspeed Chime
When an overspeed condition has occurred, the underspeed chime alerts the driver when the vehicle speed drops back below the set overspeed value.
Use the trip computer switch UP or DOWN button to select Yes or No. If Yes is selected as the option, the underspeed chime is activated.
The underspeed chime is set to Yes if the Restore to Factory Settings option has been selected. If no selection is made at the Underspeed Chime screen within 5 seconds, the Help screen message appears.
Distance to Arrival Display
Use the trip computer switch UP or DOWN button to select Yes or No. If Yes is selected as the option, the Distance to Arrival Default screen is displayed.
The Distance to Arrival Display is set to Yes if the Restore to Factory Settings option has been selected. If no selection is made at the Distance to Arrival Display screen within 5 seconds, the Help screen message appears.
Distance to Arrival Default
Use the trip computer switch UP or DOWN button to adjust the Distance to Arrival value. Note that changing this value changes the displayed Distance to Arrival figure. The default value for Distance to Arrival is 300 miles (500 km).
The Distance to Arrival Default is set to 300 miles (500 km) if the Restore to Factory Settings option has been selected. If no selection is made at the Distance to Arrival Default screen within 5 seconds, the Help screen message appears.
Rest Reminder
Use the trip computer switch UP or DOWN button to enable or disable the rest reminder. This feature reminds the driver that they may have been travelling for too long without a break.
The Rest Reminder is set to Off if the Restore to Factory Settings option has been selected. If no selection is made at the Rest Reminder screen within 5 seconds, the Help screen message appears.
Trip Computer A and B
Two trip computers can be used to record the details of separate trips. Use the trip computer switch DOWN button to select Trip A only, or press the MODE button to continue.
Trip A is enabled if the Restore to Factory Settings option has been selected. Use the trip computer switch UP button to select Trip A and Trip B, or press the MODE button to continue. If no selection is made at the Trip Computer A and B screen within 5 seconds, the Help screen message appears.
Digital Speedo
The multi function display (MFD) can be set to display a large digital speedometer display. Use the trip computer switch UP or DOWN button to select Yes or No.
The Digital Speedo is set to Yes if the Restore to Factory Settings option has been selected. If no selection is made at the Digital Speedo screen within 5 seconds, the Help screen message appears.
Stop Watch
Use the trip computer switch UP or DOWN button to select Yes or No. Press the MODE button to continue. If Yes is selected as the option, the Stop Watch screen is enabled.
The Stop Watch is set to Yes if the Restore to Factory Settings option has been selected. If no selection is made at the Stop Watch screen within 5 seconds, the Help screen message appears.
Radio Display
The entertainment system parameters can be displayed on the instrument cluster multi function display. Use the trip computer switch UP or DOWN button to select On or Off.
The Radio Display is set to On if the Restore to Factory Settings option has been selected. If no selection is made at the Radio Display screen within 5 seconds, the Help screen message appears.
Confirmation Beeps
The Confirmation Beeps screen displayed will depend on the level of the audio system fitted to the vehicle.
Confirmation Beeps - Radio Only. Confirmation beeps can be set to confirm that various functions of the entertainment system have been completed. For example storing a radio station. Use the trip computer switch UP or DOWN button to set to On or Off.
The Confirmation Beeps is set to On if the Restore to Factory Settings option has been selected. If no selection is made at the Confirmation Beeps screen within 5 seconds, the Help screen message appears.
Confirmation Beeps - Radio and CD. Confirmation beeps can be set to confirm that various functions of the entertainment system have been completed. For example storing a radio station or loading a CD. The Confirmation Beeps screen displayed indicates the current setting. The confirmation beeps can be set to On, CD Load and Eject Only or Off. Use the trip computer switch UP or DOWN button to scroll through the selection.
The Confirmation Beeps is set to On if the Restore to Factory Settings option has been selected. If no selection is made at the Confirmation Beeps screen within 5 seconds, the Help screen message appears.
Speed Dependent Volume
The entertainment system volume can be set to vary automatically with the speed of the vehicle to compensate for additional background noise. The speed dependent volume can be selected between Off / 1 / 2 / 3 / 4 / Max. Use the trip computer switch UP or DOWN button to scroll through the selection.
The Speed Dependent Volume is set to 2 if the Restore to Factory Settings option has been selected. If no selection is made at the Speed Dependent Volume screen within 5 seconds, the Help screen message appears.
Audio Distortion Limiter
The entertainment system incorporates a dynamic distortion limiting function to monitor the audio output and reduce the audio level if distortion is detected. The audio distortion limiter can be enabled or disabled. Use the trip computer switch UP or DOWN button to select On or Off.
The Audio Distortion Limiter is set to On if the Restore to Factory Settings option has been selected. If no selection is made at the Audio Distortion Limiter screen within 5 seconds, the Help screen message appears.
Headlamp Off Delay
The headlamp off delay is adjustable between zero and 180 seconds. Use the trip computer switch UP or DOWN button to increase or decrease the set value. Pressing the button once will change the value by 1 second. Press and hold the button to change the value at a faster rate.
The Headlamp Off Delay is set to 1 second if the Restore to Factory Settings option has been selected. If no selection is made at the Headlights Off Delay Time screen within 5 seconds, the Help screen message appears.
Approach Illumination
The headlamps can be set to provide illumination when approaching the vehicle at night. The approach illumination delay is adjustable between zero and 90 seconds. Use the trip computer switch UP or DOWN button to increase or decrease the set value. Pressing the button once will change the value by 1 second. Press and hold the button to change the value at a faster rate.
The Headlights Approach Time is set to 30 seconds if the Restore to Factory Settings option has been selected. If no selection is made at the Headlights Approach Time screen within 5 seconds, this Help screen message appears.
Automatic Headlamp Sensitivity
The headlamps can be set to come on automatically when lighting conditions deteriorate. The headlamp sensitivity can be set to Early, Normal or Late. Use the trip computer switch UP or DOWN button to scroll through the selection.
The Automatic Headlights Sensitivity is set to Normal if the Restore to Factory Settings option has been selected. If no selection is made at the Auto Headlights Sensitivity screen within 5 seconds, the Help screen message appears.
Interior Courtesy Lamp Timeout
The length of time that the interior courtesy lamp remains illuminated after opening a door or unlocking the vehicle is adjustable between zero and 255 seconds. Use the trip computer switch UP or DOWN button to increase or decrease the set value. Pressing the button once will change the value by 1 second. Press and hold the button to change the value at a faster rate.
The Interior Courtesy Lamp Timeout is set to 30 seconds if the Restore to Factory Settings option has been selected. If no selection is made at the Courtesy Lamp Timeout screen within 5 seconds, the Help screen message appears.
Interior Courtesy Lamp Timeout - Ignition Off
The length of time that the interior courtesy lamp remains illuminated after the ignition is turned off is adjustable between zero and 255 seconds. Use the trip computer switch UP or DOWN button to increase or decrease the set value. Pressing the button once will change the value by 1 second. Press and hold the button to change the value at a faster rate.
The Interior Courtesy Lamp Timeout - Ignition Off is set to 30 seconds if the Restore to Factory Settings option has been selected. If no selection is made at the Ignition Off Courtesy Lamp screen within 5 seconds, the Help screen message appears.
Two Stage Unlock
The vehicle can be set for two stage unlock, or unlock all doors. With two stage unlock, the first press of the unlock button on the key unlocks the drivers door only. Pressing the unlock button a second time unlocks the remaining doors. Use the trip computer switch UP or DOWN button to select Yes or No.
The Two Stage Unlock is set to Yes if the Restore to Factory Settings option has been selected. If no selection is made at the Two Stage Unlock screen within 5 seconds, the Help screen message appears.
Auto Lock In Drive
The doors can be automatically locked when the transmission is shifted from Park. This function is only available on vehicles fitted with an automatic transmission. Use the trip computer switch UP or DOWN button to select Yes or No.
The Auto Lock In Drive is set to No if the Restore to Factory Settings option has been selected. If no selection is made at the Auto Lock In Drive screen within 5 seconds, the Help screen message appears.
Door Lock Indication
The door lock indication can be selected between the turn indicators flashing or the turn indicators flashing accompanied by the sounding of the horn. The selected function also operates when unlocking the vehicle. Use the trip computer switch UP button to enable the turn indicators and horn, or the DOWN button to enable the turn indicators only.
The Door Lock Indication is set to Indicators if the Restore to Factory Settings option has been selected. If no selection is made at the Door Lock Indication screen within 5 seconds, the Help screen message appears.
Exit Options Menu
The default selection for the Exit Options Menu is Yes. Use the trip computer switch MODE button to exit the personalization Mode. The multi function display will display the previous trip computer screen. Use the trip computer DOWN button followed by the MODE button to return to the Restore to Factory Settings screen.
If no selection is made at the Exit Options Menu screen within 5 seconds, the Help screen message appears.Press the MODE button to return to the Exit Options Menu screen.
