2-Way Remote Start and Door Lock Transmitter Package Installation RHT AP3

19156553

This kit is designed to add 2-way remote start with extended range and enhanced functionality. It is for vehicles equipped with remote vehicle start from the factory (vehicles with option code AP3). If the vehicle is not equipped with remote vehicle start, but has keyless entry, use a kit for vehicles equipped with option code AP8.

Special Tools

Important: Please review this entire procedure before trying to perform it.

1. Physically replace the factory remote control door lock receiver (RCDLR) with the 2-way RCDLR included in the kit. Refer to Remote Control Door Lock Receiver Replacement. Do not program or reassemble yet.
2. Access the antenna routing path by removing the rear compartment front trim and the left side rear compartment trim. Refer to Rear Compartment Side Trim Replacement - Left Side.



3. Clean the areas of the left rear seat back panel where the antenna will be installed and the antenna cable will be secured with a surface cleaner (50 percent isopropyl alcohol, FS-1082 hi-flash naphtha or equivalent).
4. Dry the panel thoroughly using a lint-free cloth.

Important: 

•	The adhesion promoter must be used to assure adequate bonding of the antenna.

•	Mask off or protect areas before applying the adhesion promoter a=30 mm (1 3/16 in).

5. Apply Adhesion Promoter GM P/N 12378462 (Canadian P/N 10953554) to the seat back panel. Follow the instructions on the product label.



6. Use a razor blade or other sharp tool to score the protective film (1) on the antenna. Use a=50 mm (2 in) from the center of the antenna to find the locations to score (2).
7. Remove the center section (3) of protective film from the adhesive pad on the antenna. Leave the outer sections of protective film on the adhesive pad.




Important: 

•	Position the antenna according to the figure provided.

•	Do not touch the adhesive pad on the antenna.

8. Align the antenna to the panel using a=30 mm (1 3/16 in).
9. Press firmly all along the exposed area of the adhesive pad of the antenna in order to ensure proper adhesion to the trim.
10. Hold pressure on the antenna for 10-30 seconds.
11. Secure the antenna cable to the rear seat back with one adhesive wire wrap (1).



12. Secure the antenna cable to the body structure with two adhesive wire-wraps (2).
13. Secure the antenna cable to the body wiring harness with three tie wraps (1).



14. Remove the rear junction block (1) from its bracket by sliding it rearward.



15. Secure the antenna cable to the body wiring harness behind the rear junction block with one tie wrap (4).
16. Reinstall the rear junction block to its bracket.



17. Connect the antenna to the 2-Way RCDLR (3).

Important: Excess antenna cable length must be looped in a "Figure 8" no less than 100 mm (4 in) in length for the best performance of the system.

18. Loop the excess antenna cable in a "Figure 8" at least 100 mm (4 in) long and secure to the body harness remote control door lock receiver and tail lamp leads with two tie wraps (2).
19. Reassemble. Refer to Remote Control Door Lock Receiver Replacement and Rear Compartment Side Trim Replacement - Left Side.
20. Program the new RCDLR. Refer to Remote Control Door Lock Receiver Programming and Setup. Program the 2-way transmitter and the factory styled 1-way transmitter included in the kit to the 2-way RCDLR.
21. Turn the ignition off.
22. Discard the vehicle factory transmitters, as they will no longer be functional.
23. Apply the service part ID label to the bottom of the existing Service Parts ID Label. This label is for future transmitter service part identification.

23.1.

The surface temperature should not be less than 65°F (21°C).

23.2.

Clean the surface with a suitable solvent (50 percent isopropyl alcohol, FS-1062 hi-flash naphtha or equivalent).

23.3.

Dry the surface with a clean cloth.

23.4.

Peel the liner from the backside of the label, being careful not to touch the adhesive or allow dirt or any foreign material to come in contact with it.

23.5.

Carefully align the label to the surface, press firmly, and smooth out.

24. Turn the ignition on.
25. Using the scan tool, retrieve any diagnostic trouble codes (DTCs) from all of the modules.
26. Clear all DTCs.
27. Remove the scan tool.
28. Operate the 2-way and factory style 1-way transmitters in order to verify correct system operation. Refer to Keyless Entry System Description and Operation. Press a command button with the vehicle ignition ON in order to synchronize the 2-Way transmitter clock to the vehicle clock.
29. Add the transmitters to the customer key rings.
30. Place the 2-Way Advanced Remote Start owner manual in Instrument Panel Compartment.
31. Keep the vehicle dry. Allow 6-8 hours, at 15°C (60°F), for the antenna adhesive to cure after installation.

2-Way Remote Start and Door Lock Transmitter Package Installation RHT AP8

17802069

This kit is designed to add 2-way remote start with extended range and enhanced functionality. It is for vehicles not equipped with but prepped for remote vehicle start from the factory (for vehicles with option code AP8). If the vehicle is equipped with remote vehicle start, use the kit for a vehicle equipped with option code AP3. The vehicle must also have an automatic transmission. To add remote vehicle start, the vehicle needs to be reconfigured. This is done with a Service Programming System. The installer needs to call the Techline Customer Support Center (TCSC). The TCSC will ask for the Vehicle Identification Number (VIN) and the Authorization Code from the kit. The call and Authorization Code are good for only one specific VIN.

Special Tools

Important: 

•	Please review this entire procedure before trying to perform it.

•	When calling the TCSC, you must use the Authorization Code from the kit.

1. Verify the vehicle has the AP8 option and an automatic transmission. Call TCSC 1-800-828-6860 (English), 800-503-3222 (French), or 248-265-0840 (Spanish) to obtain programming instructions to add the remote start feature. You must have the vehicle VIN that will be upgraded and the Authorization Code from the kit.
2. Physically replace the factory remote control door lock receiver (RCDLR) with the 2-way RCDLR included in the kit. Refer to Remote Control Door Lock Receiver Replacement. Do not program or reassemble yet.
3. Access the antenna routing path by removing the rear compartment front trim and the left side rear compartment trim. Refer to Rear Compartment Side Trim Replacement - Left Side.



4. Clean the areas of the left rear seat back panel where the antenna will be installed and the antenna cable will be secured with a surface cleaner (50 percent isopropyl alcohol, FS-1082 hi-flash naphtha or equivalent).
5. Dry the panel thoroughly using a lint-free cloth.

Important: 

•	The adhesion promoter must be used to assure adequate bonding of the antenna.

•	Mask off or protect areas before applying the adhesion promoter a=30 mm (1 3/16 in).

6. Apply Adhesion Promoter GM P/N 12378462 (Canadian P/N 10953554) to the seat back panel. Follow the instructions on the product label.



7. Use a razor blade or other sharp tool to score the protective film (1) on the antenna. Use a=50 mm (2 in) from the center of the antenna to find the locations to score (2).
8. Remove the center section (3) of protective film from the adhesive pad on the antenna. Leave the outer sections of protective film on the adhesive pad.




Important: 

•	Position the antenna according to the figure provided.

•	Do not touch the adhesive pad on the antenna.

9. Align the antenna to the panel using a=30 mm (1 3/16 in).
10. Press firmly all along the exposed area of the adhesive pad of the antenna in order to ensure proper adhesion to the trim.
11. Hold pressure on the antenna for 10-30 seconds.
12. Secure the antenna cable to the rear seat back with one adhesive wire wrap (1).



13. Secure the antenna cable to the body structure with two adhesive wire-wraps (2).
14. Secure the antenna cable to the body wiring harness with three tie wraps (1).



15. Remove the rear junction block (1) from its bracket by sliding it rearward.



16. Secure the antenna cable to the body wiring harness behind the rear junction block with one tie wrap (4).
17. Reinstall the rear junction block to its bracket.



18. Connect the antenna to the 2-Way RCDLR (3).

Important: Excess antenna cable length must be looped in a "Figure 8" no less than 100 mm (4 in) in length for the best performance of the system.

19. Loop the excess antenna cable in a "Figure 8" at least 100 mm (4 in) long and secure to the body harness remote control door lock receiver and tail lamp leads with two tie wraps (2).
20. Reassemble. Refer to Remote Control Door Lock Receiver Replacement and Rear Compartment Side Trim Replacement - Left Side.
21. Using the Scan Tool and SPS terminal, reconfigure the vehicle for remote start. Use the method called out by the TCSC. Refer to Service Programming System (SPS).
22. Program the new RCDLR. Refer to Remote Control Door Lock Receiver Programming and Setup. Program the 2-way transmitter and the factory styled 1-way transmitter included in the kit to the 2-way RCDLR.
23. Turn the ignition off.
24. Discard the vehicle factory transmitters, as they will no longer be functional.
25. Apply the service part ID label to the bottom of the existing Service Parts ID Label. This label is for future transmitter service part identification.

25.1.

The surface temperature should not be less than 65°F (21°C).

25.2.

Clean the surface with a suitable solvent (50 percent isopropyl alcohol, FS-1062 hi-flash naphtha or equivalent).

25.3.

Dry the surface with a clean cloth.

25.4.

Peel the liner from the backside of the label, being careful not to touch the adhesive or allow dirt or any foreign material to come in contact with it.

25.5.

Carefully align the label to the surface, press firmly, and smooth out.

26. Turn the ignition on.
27. Using the scan tool, retrieve any diagnostic trouble codes (DTCs) from all of the modules.
28. Clear all DTCs.
29. Remove the scan tool.
30. Operate the 2-way and factory style 1-way transmitters in order to verify correct system operation. Refer to Keyless Entry System Description and Operation. Press a command button with the vehicle ignition ON in order to synchronize the 2-way transmitter clock to the vehicle clock.
31. Add the transmitters to the customer key rings.
32. Place the 2-Way Advanced Remote Start owner manual in Instrument Panel Compartment.
33. Keep the vehicle dry. Allow 6-8 hours, at 15°C (60°F), for the antenna adhesive to cure after installation.

2-Way Remote Start and Door Lock Transmitter Package Installation Coupe and Sedan AP3

19156553

This kit is designed to add 2-way remote start with extended range and enhanced functionality. It is for vehicles equipped with remote vehicle start from the factory (vehicles with option code AP3). If the vehicle is not equipped with remote vehicle start, but has keyless entry, use a kit for vehicles equipped with option code AP8.

Special Tools

Important: Felt/flocking tape must be applied to the rearward RCDLR mounting slot to prevent rattles with rear speaker bass.

1. Remove the factory RCDLR (2). Refer to Remote Control Door Lock Receiver Replacement.
2. Clean the sheet metal surface around the RCDLR single long (rearward) mounting slot with a surface cleaner (50 percent isopropyl alcohol, FS-1082 hi-flash naphtha or equivalent).
3. Adhere the felt/flocking tape included (if not included in the kit, cut a 23 x 23 mm (15/16 x 15/16 in) piece of felt/flocking tape BSR P/N KT13296) (1) to the rearward RCDLR mounting slot. Make sure the flocking tape wraps the edge of the slot.
4. Install the 2-way RCDLR. Do not program or reassemble yet.

Sedan

2-Way Remote Start and Door Lock Transmitter Package Installation Coupe and Sedan AP8

17802069

This kit is designed to add 2-way remote start with extended range and enhanced functionality. It is for vehicles not equipped with but prepped for remote vehicle start from the factory (for vehicles with option code AP8). If the vehicle is equipped with remote vehicle start, use the kit for a vehicle equipped with option code AP3. The vehicle must also have an automatic transmission. To add remote vehicle start, the vehicle needs to be reconfigured. This is done with a Service Programming System. The installer needs to call the Techline Customer Support Center (TCSC). The TCSC will ask for the Vehicle Identification Number (VIN) and the Authorization Code from the kit. The call and Authorization Code are good for only one specific VIN.

Special Tools

Important: 

•	Please review this entire procedure before trying to perform it.

•	When calling the TCSC, you must use the Authorization Code from the kit.

1. Verify the vehicle has the AP8 option and an automatic transmission. Call TCSC 1-800-828-6860 (English), 800-503-3222 (French), or 248-265-0840 (Spanish) to obtain programming instructions to add the remote start feature. You must have the vehicle VIN that will be upgraded and the Authorization Code from the kit.




Important: Felt/flocking tape must be applied to the rearward RCDLR mounting slot to prevent rattles with rear speaker bass.

2. Remove the factory RCDLR (2). Refer to Remote Control Door Lock Receiver Replacement.
3. Clean the sheet metal surface around the RCDLR single long (rearward) mounting slot with a surface cleaner (50 percent isopropyl alcohol, FS-1082 hi-flash naphtha or equivalent).
4. Adhere the felt/flocking tape included (if not included in the kit, cut a 23 x 23 mm (15/16 x 15/16 in) piece of felt/flocking tape BSR P/N KT13296) (1) to the rearward RCDLR mounting slot. Make sure the flocking tape wraps the edge of the slot.
5. Install the 2-way RCDLR. Do not program or reassemble yet.

Sedan