GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2006 🢒 G6 🢒 Restraints 🢒 SIR 🢒 DTC B0012 or B0013

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B0012 01: Driver Frontal Deployment Loop Stage 1 Short to Battery

DTC B0012 02: Driver Frontal Deployment Loop Stage 1 Short to Ground

DTC B0012 04: Driver Frontal Deployment Loop Stage 1 Open Circuit

DTC B0012 0D: Driver Frontal Deployment Loop Stage 1 Resistance Above Threshold

DTC B0012 0E: Driver Frontal Deployment Loop Stage 1 Resistance Below Threshold

DTC B0013 01: Driver Frontal Deployment Loop Stage 2 Short to Battery

DTC B0013 02: Driver Frontal Deployment Loop Stage 2 Short to Ground

DTC B0013 04: Driver Frontal Deployment Loop Stage 2 Open Circuit

DTC B0013 0D: Driver Frontal Deployment Loop Stage 2 Resistance Above Threshold

DTC B0013 0E: Driver Frontal Deployment Loop Stage 2 Resistance Below Threshold

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

Steering Wheel Module Stage 1 High Circuit

B0012 02

B0012 0D

B0012 04

B0012 01

B0012 0E

Steering Wheel Module Stage 1 Low Circuit

B0012 02

B0012 0D

B0012 04

B0012 01

B0012 0E

Steering Wheel Module Stage 2 High Circuit

B0013 02

B0013 0D

B0013 04

B0013 01

B0013 0E

Steering Wheel Module Stage 2 Low Circuit

B0013 02

B0013 0D

B0013 04

B0013 01

B0013 0E

Circuit/System Description

During a frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the steering wheel module. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage.

There are 2 shorting bars used within the steering wheel module coil connector which will short together both steering wheel module stage 1 high circuit and steering wheel module stage 1 low circuit and both steering wheel module stage 2 high circuit and steering wheel module stage 2 low circuit when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0012 01 Stage 1 or B0013 01 Stage 2

The steering wheel module high and/or low circuit is short to voltage for 120 milliseconds.

B0012 02 Stage 1 or B0013 02 Stage 2

The steering wheel module high and/or low circuit is short to ground for 120 milliseconds.

B0012 04 Stage 1 or B0013  04 Stage 2

The steering wheel module high and/or low circuit is open for 120 milliseconds.

B0012 0D Stage 1 or B0013 0D Stage 2

The steering wheel module deployment loop resistance is more than 5.1 ohms for 120 milliseconds.

B0012 0E Stage 1 or B0013 0E Stage 2

The steering wheel module deployment loop resistance is less than 1.3 ohms for 120 milliseconds.

Action Taken When the DTC Sets
    • The SDM commands the AIR BAG indicator ON via serial data communications.
    • The SIR system is disabled and no deployments are allowed.

Conditions for Clearing the DTC
    • The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
    • A history DTC will clear once 255 malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

SIR Schematics

Connector End View Reference

SIR Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Special Tools Required

    • J 38715-A SIR Driver/Passenger Load Tool
    • J38715-80 Driver/Passenger Load Tool Adapter
    • EL38715-120 SIR Load Tool Adapter (Top of Column)
    • EL38715-140 SIR Load Tool Adapter (Back of Steering Wheel Coil)

Circuit/System Testing

Important: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector.

   • The pretensioner
   • The air bag module
   • The SDM module
   • The air bag wiring harness connector
   • The SDM wiring harness connector

  1. Verify that the steering wheel module connector and the connector position assurance (CPA) are engaged.

    2. Important: The connector and CPA may seat independent of each other. Both the connector and CPA should seat with an audible and/or tactile click. The CPA isolates the shorting-bars within the connector allowing the deployment circuit to operate properly.

    ⇒If the above condition is found, make the appropriate repair.
  2. Ignition OFF, disconnect the steering wheel module.
  3. With the applicable adaptor, connect special tool J 38715-A .
  4. Ignition ON, with a scan tool, verify DTC is set as current.
    5. ⇒If DTC is not set or is set as history, replace the steering wheel module.
  5. Ignition OFF, disconnect special tool J 38715-A .
  6. Disconnect the steering wheel module coil in-line connector.
  7. With the applicable adaptor, connect special tool J 38715-A .
  8. Ignition ON, with a scan tool, verify DTC is set as current.
    9. ⇒If DTC is not set or is set as history, replace the steering wheel module coil.
  9. Ignition OFF, disconnect special tool J 38715-A and the applicable adaptor.
  10. Ignition ON, test for less than 1 volt between the applicable HI circuit and ground.
    11. ⇒If not the specified range, test the circuit for a short to voltage.
  11. Test for less than 1 volt between the applicable LOW circuit and ground.
    12. ⇒If not the specified range, test the circuit for a short to voltage.
  12. Ignition OFF, test for infinite resistance between the applicable HI circuit and ground.
    13. ⇒If not the specified range, test the circuit for a short to ground.
  13. Test for infinite resistance between the applicable LOW circuit and ground.
    14. ⇒If not the specified range, test the circuit for a short to ground.
  14. Disconnect the harness connector at the SDM.
  15. Test for less then 1 ohm of resistance between the SDM connector and the air bag module connector HI circuit.
    16. ⇒If not the specified range, test the circuit for an open/high resistance.
  16. Test for less then 1 ohm of resistance between the SDM connector and the air bag module connector LOW circuit.
    17. ⇒If not the specified range, test the circuit for an open/high resistance.
  17. If all circuits test normal, replace the SDM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Inflatable Restraint Steering Wheel Module Coil Replacement
    •  Inflatable Restraint Steering Wheel Module Replacement
    •  Control Module References for SDM replacement, setup, and programming