Power Requirements
The BCM has three main voltage feeds and three grounds. The voltage
feed circuits are used to provide power for the BCM's logic, courtesy lights,
internal driver operation and the door locks.
BCM Inputs
The following components provide direct input to the BCM, plus other
systems can use this input information in order to carry out certain functions:
| • | Accessory Signal Input (ACCESSORY 1): Provides accessory power
for the BCM. |
| • | Battery Power 2: Provides the BCM power for the door locks. |
| • | Battery Power 3: Provides the BCM power for the inadvertant power
relay. |
| • | BCM Ground: Provides ground for BCM operation. |
| • | BCM Power: Provides voltage for BCM operation. |
| • | Courtesy Lights On Input (Courtesy Switch): Determines when the
dome lamp switch (Headlamp Switch) is closed to request the dome lamp on. |
| • | Courtesy Ground: Provides ground to the courtesy lights. |
| • | Crank Signal: Determines when the ignition switch is in the start
position. |
| • | Door Lock Switch: Door lock switch request to lock the vehicle
doors. |
| • | Door Open: Provides door ajar status. |
| • | Door Unlock Switch: Door lock switch request to unlock
the vehicle doors. |
| • | Driver Door Open: Allows certain chime functions when the driver's
door is open. |
| • | Driver Seat Belt Unfastened Input (Seat Belt Status): Determines
when the driver seat belt is unfastened. |
| • | DRL Signal Low: This input provides the BCM with Information through
an ambient light sensor for the DRL feature. |
| • | Exterior Lamps Off Input: Determines when the headlamp switch
is in the OFF position. |
| • | Ground 2: Provides the BCM, internal door relays, with ground. |
| • | Headlamp Switch Input: Determines when the Headlamp relay is energized |
| • | Ignition 0: Determines when the ignition switch is in theOFF,
RUN or START position. |
| • | Ignition 1: Determines when the ignition switch is in the RUN
or START positions. |
| • | Key In Ignition: Determines when the key is fully inserted in
the ignition key cylinder. |
| • | Left Turn Switch: Determines if the Left Turn Switch has been
activated. |
| • | Park Brake Applied Switch Input: Determines when the parking brake
is applied. |
| • | PASSLOCK Sensor Data Input: Provides the BCM with PASSLOCK information. |
| • | Performance Shift Switch Input: Determines if the Performance
Shift Switch has been switched. |
| • | Rear Compartment Ajar (Trunk Ajar Switch): Determines if the rear
decklid is open or closed. |
| • | RFA Link: Provides an interface allowing the transfer of keyless
entry information from the Remote Control Door Lock Receiver (RCDLR). |
| • | Right Turn Switch: Determines if the Right Turn Switch has been
activated. |
| • | Serial Data Class 2: Provides an interface with the PCM, EBCM,
Heater A/C Control, SDM and the IPC through the Class 2 serial data link. |
| • | Theater Dimming 1 Ground: Provides ground for Theater Dimming
1 control. |
| • | Traction Control Request (TCS Switch): This input provides the
BCM with a request for Traction Control through a momentary switch connected
to ground. |
BCM Outputs
The BCM directly controls these outputs, plus other systems may request
the BCM to control these outputs for certain functions:
| • | All Door Lock: This output supplies voltage to the door lock actuators
when the doors are commanded to lock. This output also supplies ground to
all the door lock actuators when the doors are commanded to unlock. |
| • | Courtesy Lamps Switched Feed: Provides courtesy lamps with power. |
| • | Driver Door Unlock: This output supplies voltage to the driver
door lock actuators when the doors are commanded to unlock. This output also
supplies ground to the driver door lock actuator when the doors are
commanded to lock. |
| • | DRL 5V Reference: Provides 5 volts to the ambient light sensor. |
| • | DRL Link: Provides ground to the Headlamp relay control ciruit. |
| • | Fog Lamp Enable (Front Fog Lamp Relay): Sends a ground signal
to the fog lamp switch when the ignition switch is on, this action enables
the fog lamp switch. The fog lamps turn on when the fog lamp switch
is enabled by the BCM. |
| • | Headlamp Relay Control (Headlamps): Provides ground to the Headlamp
relay control ciruit. |
| • | Horn Output: Sends a ground signal to the horn relay, sounding
the horn for the keyless entry alarm function or the content theft system. |
| • | Park Lamp Relay Control (Park Lamps): Provides ground to the Park
Lamp relay control ciruit. |
| • | Passenger Door Unlock: This output supplies voltage to the door
lock actuators (except the driver door lock actuator) when the doors are
commanded to unlock. This output also supplies ground to all the door
lock actuators (except the driver door lock actuator) when the doors
are commanded to lock. |
| • | PASSLOCK Sensor Ground: Provides the PASSLOCK sensor with ground. |
| • | PASSLOCK Sensor Power Output: Provides the PASSLOCK sensor with
power. |
| • | RAP Relay Control (RAP Output): Provides ground to the RAP relay
control ciruit. |
| • | RFA Link: Provides an interface allowing the transfer of keyless
entry information to the Remote Control Door Lock Receiver (RCDLR). |
| • | Serial Data Class 2: Provides an interface with the PCM, EBCM,
Heater A/C Control, SDM and the IPC through the Class 2 serial data link. |
| • | Theater Dimming 1Control: Supplies ground to activate the interior
lamps. |
