GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 1999 🢒 Savana 🢒 Body and Accessories 🢒 Doors 🢒 Heated Mirrors Inoperative

Heated Mirrors Inoperative Domestic

Step

Action

Value(s)

Yes

No

1

Was the Heated Mirror System Check performed?

--

Go to Step 2

Go to Heated Mirror System Check

2
  1. Ensure that the HTD MIR fuse and the HTR-A/C fuse are in good condition.
  2. Ensure all grounds are clean and tight.
  3. Disconnect C210 connector at the convenience center.
  4. Connect an unpowered test lamp between C210, pin C2, and ground.
  5. Place the ignition switch to the RUN position.
  6. Depress the heated mirror pushbutton on the heater and A/C controller.

Does the test lamp light?

--

Go to Step 8

Go to Step 10

3
  1. Disconnect the C211 connector or the C212 connector.
  2. Connect a J 39200 between connector C211/C212, pin E, and ground G201, or ground G200 on vehicles with upfitter provisions.

Is continuity present?

--

Go to Step 4

Go to Step 9

4
  1. Connect the C211/C212 connector.
  2. Disconnect the heater and A/C controller connector C3.
  3. Connect a J 39200 between the heater and A/C controller connector C3, cavity D, and the convenience center, pin C2.

Is continuity present?

--

Go to Step 5

Go to Step 10

5

Connect an unpowered test lamp between heater and A/C controller connector C3, cavity A, and ground.

Does the test lamp light?

--

Go to Step 6

Go to Step 11

6

Connect an unpowered test lamp between heater and A/C controller connector C3, cavity B, and ground.

Does the test lamp light?

--

Go to Step 7

Go to Step 12

7

Connect a J 39200 between the heater and A/C controller connector C3, cavity C, and ground.

Is continuity present?

--

Go to Step 13

Go to Step 14

8
  1. Inspect connector C210, cavity C2, for a loose or damaged connection.
  2. Refer to Connector Repairs .

Was a condition found and repaired on the connector?

--

Go to Heated Mirror System Check

Go to Step 3

9

Repair the open in CKT 150 (BLK) between splice S206 and ground G201/G200.

Refer to Wiring Repairs .

Is the repair complete?

--

Go to Heated Mirror System Check

--

10

Repair the open in CKT 267 (ORN) between the heater and A/C controller connector and the convenience center.

Refer to Wiring Repairs .

Is the repair complete?

--

Go to Heated Mirror System Check

--

11

Repair the open in CKT 1440 (ORN) between the IP fuse block and the heater and A/C controller.

Refer to Wiring Repairs .

Is the repair complete?

--

Go to Heated Mirror System Check

--

12

Repair the open in CKT 141 (BRN) between the IP fuse block and the heater and A/C controller.

Refer to Wiring Repairs .

Is the repair complete?

--

Go to Heated Mirror System Check

--

13

Replace the heater and A/C controller.

Refer to Control Assembly Replacement .

Is the repair complete?

--

Go to Heated Mirror System Check

--

14

Repair the open in CKT 150 (BLK) between the heater and A/C controller and ground G201.

Refer to Wiring Repairs .

Is the repair complete?

--

Go to Heated Mirror System Check

--

Heated Mirrors Inoperative Export

Step

Action

Value(s)

Yes

No

1

Was the Heated Mirror System Check performed?

--

Go to Step 2

Go to Heated Mirror System Check

2

Are both heated mirrors inoperative?

--

Go to Step 3

Go to Step 16

3
  1. Disconnect connector C211 or connector C212.
  2. Connect a J 39200 between connector C211/C212, pin E, and ground G201, or ground G200 on vehicles with upfitter provisions.

Is continuity present?

--

Go to Step 5

Go to Step 4

4

Repair the open in CKT 150 (BLK) between splice S206 and ground G201/G200.

Are both heated mirrors operative?

--

Go to Heated Mirror System Check

Go to Step 5

5
  1. Reconnect connector C211/C212.
  2. Disconnect connector C210 at the convenience center.
  3. Connect an unpowered test lamp between C210, pin C2, and a known good ground.
  4. Turn the ignition switch to the RUN position.
  5. Depress the heated mirror switch.

Does the test lamp light?

--

Go to Step 6

Go to Step 7

6
  1. Inspect connector C210, cavity C2, for a loose or damaged connection.
  2. Repair the connection, as necessary.

Are both heated mirrors operative?

--

Go to Heated Mirror System Check

Go to Step 7

7
  1. Disconnect connector C3 at the heater and A/C controller.
  2. Connect a J 39200 between heater and A/C controller connector C3, cavity D, and the convenience center, pin C2 for connector C210.

Is continuity present?

--

Go to Step 9

Go to Step 8

8

Repair the open in CKT 267 (ORN) between the heater and A/C controller connector and the convenience center.

Are both heated mirrors operative?

--

Go to Heated Mirror System Check

Go to Step 9

9

Connect an unpowered test lamp between heater and A/C controller connector C3, cavity A, and a known good ground.

Does the test lamp light?

--

Go to Step 11

Go to Step 10

10

Repair the open in CKT 1440 (ORN) between the IP fuse block and the heater and A/C controller.

Are both heated mirrors operative?

--

Go to Heated Mirror System Check

Go to Step 11

11
  1. Connect an unpowered test lamp between heater and A/C controller connector C3, cavity B, and a known good ground.
  2. Place the ignition switch in the RUN position.

Does the test lamp light?

--

Go to Step 13

Go to Step 12

12

Repair the open in CKT 141 (BRN) between the IP fuse block and the heater and A/C controller.

Are both heated mirrors operative?

--

Go to Heated Mirror System Check

Go to Step 13

13

Connect a J 39200 between heater and A/C controller connector C3, cavity C, and a known good ground.

Is continuity present?

--

Go to Step 15

Go to Step 14

14

Repair the open in CKT 150 (BLK) between the heater and A/C controller and ground G201.

Are both heated mirrors operative?

--

Go to Heated Mirror System Check

Go to Step 15

15

Replace the heater and A/C controller.

Are both heated mirrors operative?

--

Go to Heated Mirror System Check

Go to Step 16

16

Is the left heated mirror operative?

--

Go to Step 22

--

17
  1. Disconnect the connector at the left power outside rearview mirror.
  2. Connect a J 39200 between the power outside rearview mirror connector, cavity A, and a known good ground.

Is continuity present?

--

Go to Step 19

Go to Step 18

18

Repair the open in CKT 150 (BLK) between the left power outside rearview mirror and splice 206.

Is the left heated mirror operative?

--

Go to Heated Mirror System Check

Go to Step 19

19
  1. Connect an unpowered test lamp between the left power outside rearview mirror connector, cavity H, and a known good ground.
  2. Actuate the heated mirror pushbutton on the heater and A/C controller.

Does the test lamp light?

--

Go to Step 21

Go to Step 20

20

Repair the open in CKT 267 (ORN) between convenience center connector C210 and the left power outside rearview mirror.

Is the left heated mirror operative?

--

Go to Heated Mirror System Check

Go to Step 21

21

Replace the left power outside rearview mirror.

Is the repair complete?

--

Go to Heated Mirror System Check

Go to Step 22

22
  1. Disconnect the connector at the right power outside rearview mirror.
  2. Connect a J 39200 between the power outside rearview mirror connector, cavity A, and a known good ground.

Is continuity present?

--

Go to Step 24

Go to Step 23

23

Repair the open in CKT 150 (BLK) between the right power outside rearview mirror and splice 206.

Is the right heated mirror operative?

--

Go to Heated Mirror System Check

Go to Step 24

24
  1. Connect an unpowered test lamp between the right power outside rearview mirror connector, cavity H, and a known good ground.
  2. Actuate the heated mirror pushbutton on the heater and A/C controller.

Does the test lamp light?

--

Go to Step 26

Go to Step 25

25

Repair the open in CKT 267 (ORN) between convenience center connector C210 and the right power outside rearview mirror.

Is the right heated mirror operative?

--

Go to Heated Mirror System Check

Go to Step 26

26

Replace the right power outside rearview mirror.

Is the right heated mirror operative?

--

Go to Heated Mirror System Check

--