The 1-2 shift solenoid (SS) valve controls the fluid flow action on the 1-2 and the 3-4 shift valves. The 1-2 SS valve is a normally-open exhaust valve that is used with the 2-3 SS in order to allow four different shifting combinations.
When the powertrain control module (PCM) detects a 1-1-4-4 gear ratio, then DTC P0752 sets. DTC P0752 is a type C DTC. For California emissions vehicles and vehicles under 8,600 GVW, DTC P0752 is a type B DTC.
• | No MAP sensor DTCs P0106, P0107, or P0108. |
• | No transmission component slipping DTC P0894. |
• | No TP sensor DTCs P0120 or P0220. |
• | No ISS sensor DTCs P0716 or P0717. |
• | No VSS DTCs P0502 or P0503. |
• | No MAF DTC P0101, P0102, or P0103. |
• | No TFP manual valve position switch DTC P1810. |
• | No shift solenoid electrical DTC P0753 or P0758. |
• | Not in 4WD Low. |
• | No TCC PWM solenoid valve DTC P2761. |
• | No TCC Stuck On DTC P0742. |
• | The engine is running for greater than 7 seconds. |
• | The system voltage is 10-18 volts. |
• | Transmission ISS is greater than 7 RPM. |
• | Transmission OSS is greater than 7 RPM. |
• | The TP sensor is greater than 10 percent. |
• | The engine torque must be 108-542 N·m (80-400 lb ft). |
• | No TFP manual valve position switch change within 6 seconds. |
• | The TFP manual valve position switch indicates D4. |
• | The transmission fluid temperature (TFT) is 20-130°C (68-266°F). |
• | The commanded gear equals 2nd and the ratio equals 1st for greater than 2.25 seconds. |
• | All conditions are met for 5 occurrences. |
• | For California emission equipped vehicles, the PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. For Federal emission equipped vehicles, the MIL is not illuminated. |
• | The PCM commands maximum line pressure. |
• | The PCM inhibits 3-2 downshifts above 40 km/h (25 mph). |
• | The PCM freezes shift adapts. |
• | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame, California only, and Failure Records, California and Federal. |
• | The PCM stores the DTC P0752 in PCM history during the second consecutive trip, California, or the first trip, Federal, in which the Conditions for Setting the DTC are met. |
• | For California emissions, the PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
• | A scan tool can clear the MIL/DTC. |
• | For California emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring. |
• | For Federal emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without a non-emission related diagnostic fault occurring. |
• | The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM. |
• | Verify that the transmission meets the specifications in the Shift Speed table. Refer to Shift Speed . |
• | Other internal transmission failures may cause incorrect gear ratios to occur. Refer to Shift Solenoid Valve State and Gear Ratio . |
• | DTC P0752 defaults to an elevated line pressure condition which may result in partial TCC apply. This may produce an idle surge that could stall the engine. |
The number below refers to the step number on the diagnostic table.
Step | Action | Value(s) | Yes | No | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Engine Controls? | -- | Go to Step 2 | Go to Diagnostic System Check - Engine Controls in Engine Controls - 4.8L, 5.3L, and 6.0L | ||||||||||||
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM. Did you detect a 1-1-4-4 shift pattern? | -- | Go to Step 3 | Go to Intermittent Conditions in Engine Controls - 4.8L, 5.3L, and 6.0L | |||||||||||||
3 |
Refer to Control Valve Body Cleaning and Inspection in Transmission Unit Repair Manual. Did you find and correct the condition? | -- | Go to Step 4 | -- | ||||||||||||
4 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | Go to Step 5 | Go to Step 2 | ||||||||||||
5 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List in Engine Controls - 4.8L, 5.3L, and 6.0L | System OK |