Rear License Plate Lamp Replacement 2 Door

1. Remove the endgate outside handle. Refer to Endgate Handle Replacement in Body Rear End.
2. Remove the 2 bolts (1) which secure the rear license plate housing.
3. Remove the following components from the rear license plate housing:

3.1.	The 2 screws

3.2.	The rear license plate

4. Using a taped flat bladed tool in order to gently pry the housing from the endgate panel by disengaging the plastic retainers.



5. Remove the gasket (2) from the rear license plate housing (1).



6. Remove the 2 screws (2) which secure the rear license plate lamp assembly (1).
7. Pull the lamp assembly (1) rearward in order to gain access to the rear license plate lamp electrical connector.
8. Disconnect the rear license plate lamp electrical connector.
9. Remove the rear license plate lamp assembly (1) from the rear license plate housing (3).



10. Remove the rear license plate lamp bulb socket (1) from the lamp assembly (2), if necessary.
11. Remove the rear license plate lamp bulb from the license plate lamp bulb socket (1), if necessary.

1. Install the rear license plate lamp bulb to the rear license plate lamp bulb socket (1), if removed.
2. Install the license plate lamp bulb socket (1) to the lamp assembly (2), if removed.



3. Connect the rear license plate lamp electrical connector.
4. Install the rear license plate lamp assembly (1) to the rear license plate housing (3). Secure the assembly with the 2 screws (2).



5. Install the gasket (2) to the housing (1).



6. Install the rear license plate housing to the endgate panel. Ensure that the plastic retainers are fully engaged.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

7. Install the 2 bolts (1) which secure the rear license plate housing.

Tighten
Tighten the rear license plate housing mounting bolts to 10 N·m (89 lb in).

8. Install the rear license plate to the housing. Secure the license plate with the 2 screws.
9. Install the endgate outside handle. Refer to Endgate Handle Replacement in Body Rear End.

Rear License Plate Lamp Replacement 4 Door

1. Remove the rear door outside handle. Refer to Rear Door Outside Handle Replacement in Body Rear End.
2. Remove the 2 bolts (1) that retain the rear license plate housing.
3. Remove the following components from the rear license plate housing:

3.1.	The 2 screws

3.2.	The rear license plate

4. Using a taped flat bladed tool in order to gently pry the housing from the rear door by disengaging the plastic retainers.



5. Remove the gasket (2) from the housing (1).



6. Remove the 2 screws (2) that retain the rear license plate lamp assembly (1).
7. Pull the lamp assembly (1) rearward in order to gain access to the rear license plate lamp electrical connector.
8. Disconnect the rear license plate lamp electrical connector.
9. Remove the rear license plate lamp assembly (1) from the rear license plate housing (3).



10. Remove the rear license plate lamp bulb socket (1) from the lamp assembly (2), if necessary.
11. Remove the rear license plate lamp bulb from the license plate lamp bulb socket (1), if necessary.

1. Install the license plate lamp bulb to the license plate lamp bulb socket (1), if removed.
2. Install the license plate lamp bulb socket (1) to the lamp assembly (2), if removed.



3. Connect the rear license plate lamp electrical connector.
4. Install the rear license plate lamp assembly (1) to the rear license plate housing (3). Secure the assembly with the 2 screws (2).



5. Install the gasket (2) to the housing (1).



6. Install the rear license plate housing to the rear door. Ensure that the plastic retainers are completely engaged.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

7. Install the 2 bolts (1) that retain the rear license plate housing.

Tighten
Tighten the rear license plate housing mounting bolts to 10 N·m (89 lb in).

8. Install the rear license plate to the housing. Secure the license plate with the 2 screws.
9. Install the rear door outside handle. Refer to Rear Door Outside Handle Replacement in Body Rear End.