DTC P1715. Chevrolet Captiva 2007

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 2007 🢒 Captiva 🢒 DTC 🢒 DTC P1715

This diagnostic procedure supports the following DTC:

DTC P1715

•	Mode selector is tiptronic mode.

•	Output speed is 500-1,260 RPM.

•	The elapsed time is 2 seconds after changing to the shift position (range 2).

•	0.5 second passes after shifting control.

•	Throttle is 0 percent.

•	Transmission fluid Temperature is 20°C (68°F) or greater.

•	Engine speed is greater than 400 RPM.

•	System voltage is 10.5 volts or greater.

•	No shifting

•	No N-D shifting

•	No failure detection of output speed sensor, input speed sensor, selector position, shift solenoid, lockup slip, linear solenoid, engine RPM, engine torque, throttle, transmission fluid temperature sensor

Current gear is 1st gear--Current 1st gear ratio/expected 1st gear ratio is greater than 20 percent of the expected 1st gear ratio for 12 seconds.

•	TCM will request the illumination of MIL.

•	TCM records the operating condition when the Conditions for Setting the DTC are met. TCM stores this information as Failure Record.

•	TCM stores DTC in TCM history.

•	TCM requests the engine control module (ECM) to limit engine torque to 150 N·m (111 lb ft).

•	TCM turns Emergency mode ON

•	When the Emergency mode is ON, the following conditions occur :

-	The transmission will operate in 4th gear when the transmission is shifted into D, M+, or 4th gear range.

-	The transmission will operate in 2nd gear when the transmission is shifted into 2 or M- range.

-	Learn control is disabled.

-	Lock up control is disabled.

-	Adaptive control is disabled.

-	N-D shifting is disabled.

-	ABS function is disabled.

•	The MIL turns OFF when no failure is detected for three consecutive driving cycles.

•	The scan tool can clear the DTC from the TCM history.

•	TCM clears the DTC from the TCM history memory after forty consecutive warm-up cycles without fault.

•	Shift Solenoid (SS) 1 (Stuck OFF)

•	Shift Solenoid (SS) 2 (Stuck ON)

•	Line Pressure Control (PC) Solenoid (Stuck OFF)

-	Inside Valve Body

TCM

Step	Action	Value(s)	Yes	No
1	Turn the ignition OFF. Install the Scan tool. With the engine OFF, turn the ignition switch to the ON position. Select Store Freeze Frame/Failure Records from the Diagnostic Trouble Codes Information menu. Store Freeze Frame/Failure Records. Select Clear DTC Information from the Diagnostic Trouble Codes Information menu. Clear DTC Information. Perform one vehicle drive cycle. Is the Malfunction Indicator Lamp (MIL) ON?	--	Go to Step 2	Repair the temporary connection failure of connector. Refer to Repairing Connector Terminals.
2	Select Request DTC by Status from the Diagnostic Trouble Codes Information menu. Request DTC by Status. Is DTC P1715 displayed?	--	Go to Step 3	Repair the temporary connection failure of connector. Refer to Repairing Connector Terminals.
3	Turn the ignition OFF. Replace the master TCM and perform simulation test again under user condition. Is DTC P1715 reappeared?	--	Go to Step 4	Replace the TCM.
4	Estimate the failure of shift solenoid 1, shift solenoid 2, line pressure control (PC) solenoid or internal valve body. Inspect the SS1 or SS2. Is the condition of SS1 or SS2 OK?	--	Replace the valve body assembly. Refer to Control Valve Body Replacement.	Replace shift solenoid 1 (SS1) or shift solenoid 2 (SS2).