GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2000 🢒 Camaro 🢒 Body and Accessories 🢒 Exterior Trim 🢒 Exterior Trim Molding/Nameplate Replacement

Exterior Trim Molding/Nameplate Replacement Z28 Fender Emblem

Tools Required

J 25070 Heat Gun

Removal Procedure

    Object Number: 369038 Size: SH
  1. Mark the position of the emblem/nameplate with a length of masking tape.
  2. Heat the emblem/nameplate using the J 25070 .
  3. Apply heat using a circular motion for about 30 seconds.

    4. Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

  4. Remove the emblem/nameplate from the door panel using a plastic flat-bladed tool.
  5. Wash the fender with soapy water and wipe dry.
  6. Remove all traces of adhesive from the fender using a oil-free naptha or alcohol.

Installation Procedure

    Object Number: 369042 Size: SH

    Important: Do not touch the adhesive backing on the emblem/nameplate.

  1. Remove the backing from the emblem/nameplate.
  2. Measure 51.5 mm (2.03 in) from the front edge of the door to the rear edge of the emblem/nameplate (1).
  3. Measure 32.0 mm (1.25 in) from the bottom edge of the emblem/nameplate (1) to the top edge of the molding (2).

    4. Object Number: 369038 Size: SH
  4. Align the emblem/nameplate to the tape guideline and press firmly in place.

Exterior Trim Molding/Nameplate Replacement Trans Am Door Emblem

Tools Required

J 25070 Heat Gun

Removal Procedure

    Object Number: 369045 Size: SH
  1. Mark the position of the emblem/nameplate with a length of masking tape.
  2. Heat the emblem/nameplate using the J 25070 .
  3. Apply heat using a circular motion for about 30 seconds.

    4. Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

  4. Remove the emblem/nameplate from the door using a plastic flat-bladed tool.
  5. Wash the door with soapy water and wipe dry.
  6. Remove all traces of adhesive from the door using a oil-free naptha or alcohol.

Installation Procedure

    Object Number: 369046 Size: SH

    Important: Do not touch the adhesive backing on the emblem/nameplate.

  1. Remove the backing from the emblem/nameplate.
  2. Measure 40.0 mm (1.6 in) from the front edge of the door to the front edge of the emblem/nameplate (2).
  3. Measure 14.0 mm (0.55 in) from the top edge of the emblem (2) to the bottom edge of the molding (1).

    4. Object Number: 369045 Size: SH
  4. Align the emblem/nameplate to the tape guideline and press firmly in place.

Exterior Trim Molding/Nameplate Replacement Firebird/Formula Door Emblem

Tools Required

J 25070 Heat Gun

Removal Procedure

    Object Number: 369048 Size: SH
  1. Mark the position of the emblem/nameplate (1 or 2) with a length of masking tape.
  2. Heat the emblem/nameplate (1 or 2) using the J 25070 .
  3. Apply heat using a circular motion for about 30 seconds.

    4. Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

  4. Remove the emblem/nameplate from the rear end finish panel using a plastic flat-bladed tool.
  5. Wash the door with soapy water and wipe dry.
  6. Remove all traces of adhesive from the door using a oil-free naptha or alcohol.

Installation Procedure

    Object Number: 369056 Size: SH

    Important: Do not touch the adhesive backing on the emblem/nameplate.

  1. Remove the backing from the emblem/nameplate.
  2. Measure 53.0 mm (2.09 in) from the front edge of the door to the front edge of the emblem (1).

    3. Object Number: 369048 Size: SH
  3. Align the emblem/nameplate (1 or 2) to the tape guideline and press firmly in place.

Exterior Trim Molding/Nameplate Replacement Z28 Fender Emblem Export

Tools Required

J 25070 Heat Gun

Removal Procedure

    Object Number: 369059 Size: SH
  1. Mark the position of the emblem/nameplate with a length of masking tape.
  2. Heat the emblem/nameplate using the J 25070 .
  3. Apply heat using a circular motion for about 30 seconds.

    4. Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

  4. Remove the emblem/nameplate from the fender using a plastic flat-bladed tool.
  5. Wash the door with soapy water and wipe dry.
  6. Remove all traces of adhesive from the fender using a oil-free naptha or alcohol.

Installation Procedure

    Object Number: 369061 Size: SH

    Important: Do not touch the adhesive backing on the emblem/nameplate.

  1. Remove the backing from the emblem/nameplate.
  2. Measure 36.0 mm (1.42 in) from the rear edge of the fender to the rear edge of the emblem (2).
  3. Measure 50.5 mm (2.0 in) from the top edge of the molding to the tope edge of the emblem/nameplate (1).

    4. Object Number: 369059 Size: SH
  4. Align the emblem/nameplate to the tape guideline and press firmly in place.

Exterior Trim Molding/Nameplate Replacement Z28 Rear End Finish Panel

Tools Required

J 25070 Heat Gun

Removal Procedure

    Object Number: 369109 Size: SH
  1. Mark the position of the emblem/nameplate with a length of masking tape.
  2. Heat the emblem/nameplate using the J 25070 .
  3. Apply heat using a circular motion for about 30 seconds.

    4. Notice: Use a plastic, flat-bladed tool to prevent paint damage when removing an emblem/name plate.

  4. Remove the emblem/nameplate from the rear bumper fascia using a plastic, flat-bladed tool.
  5. Wash the rear fascia with soapy water and wipe dry.
  6. Remove all traces of adhesive from the fascia using oil-free naptha or alcohol.

Installation Procedure

    Object Number: 369112 Size: SH

    Important: Do not touch the adhesive backing on the emblem/nameplate.

  1. Remove the backing from the emblem/nameplate.
  2. Measure 164.0 mm (6.46 in) from the outer edge of the tail lamp lens (3) to the edge of the emblem/nameplate (2).
  3. Measure 16.0 mm (0.63 in) from the bottom edge of the rear bumper fascia (1) to the bottom edge of the emblem/nameplate (2).

    4. Object Number: 369109 Size: SH
  4. Align the emblem/nameplate to the tape guideline and press firmly in place.