Circuit Description
The speed sensor used on this vehicle is a multiple pole magnetic pickup. This sensor produces an AC signal that the EBCM uses the frequency from to calculate the wheel speed.
Conditions for Setting the DTC
The DTC can be set any time the ignition is in the RUN position and the EBCM detects an open or a short to voltage.
Action Taken When the DTC Sets
| • | A malfunction DTC stores. |
| • | The ABS/TCS disables. |
| • | The amber ABS/TCS indicator(s) turn on. |
| • | The Red BRAKE Warning indicator could turn on. |
Conditions for Clearing the DTC
| • | The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used. |
| • | 100 ignition cycles pass with no DTC(s) detected. |
Diagnostic Aids
| • | It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction. |
| • | Thoroughly inspect any circuitry that may be causing the complaint for the following conditions: |
| - | Backed out terminals |
| - | Improper mating |
| - | Broken locks |
| - | Improperly formed or damaged terminals |
| - | Poor terminal-to-wiring connections |
| - | Physical damage to the wiring harness |
| • | The following conditions may cause an intermittent malfunction: |
| - | A poor connection |
| - | Rubbed-through wire insulation |
| - | A broken wire inside the insulation |
| • | If the customer's comments reflect that the amber ABS/TCS indicator is on only during moist environmental conditions (rain, snow, vehicle wash), inspect all the wheel speed sensor circuitry for signs of water intrusion. If the DTC is not current, clear all DTCs and simulate the effects of water intrusion by using the following procedure: |
| 1. | Spray the suspected area with a five percent saltwater solution. |
Add two teaspoons of salt to twelve ounces of water to make a five percent saltwater solution.
| 2. | Test drive the vehicle over various road surfaces (bumps, turns, etc.) above 40 km/h (25 mph) for at least 30 seconds. |
| 3. | If the DTC returns, replace the suspected harness. |
| • | If an intermittent malfunction exists refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
Front Wheel Speed Sensor Resistance
Use the following table that contains resistance values for the front wheel speed sensors at varying sensor temperatures for use in diagnosis. The values are approximate and should be used as a guideline for diagnosis. Refer to ABS Diagnostic Specifications .
Test Description
The numbers below refer to step numbers on the diagnostic table.
-
This step checks for an open in the WSS or WSS CKT.
-
Checks for a short to voltage in the WSS CKT.
-
Checks for a short to voltage in the WSS CKT.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Diagnostic System Check performed? | -- | ||
2 | Inspect the WSS for physical damage. Is physical damage of the WSS evident? | -- | ||
3 | Replace the WSS. Refer to Wheel Speed Sensor Replacement in Front Suspension. Is the replacement complete? | -- | -- | |
4 | Inspect the jumper harness for physical damage. Is physical damage of the jumper harness evident? | -- | ||
5 | Replace the jumper harness. Refer to Wheel Speed Sensor Jumper Harness Replacement . Is the replacement complete? | -- | -- | |
Is the resistance within the range specified in the value(s) column? | 800-1600 ohms | |||
7 |
Is the resistance within the range specified in the value(s) column? | 800-1600 ohms | ||
8 | Using J 39200 DMM, measure the resistance between terminal 20 of J 39700 and terminal B of the WSS harness connector. Is the resistance within the range specified in the value(s) column? | 0-5ohms | ||
9 | Repair CKT 830 for an open or high resistance. Refer to Wiring Repairs . If an open or high resistance is found in the jumper harness, replace the jumper harness. Refer to Wheel Speed Sensor Jumper Harness Replacement . Is the repair complete? | -- | -- | |
10 | Using J 39200 DMM, measure the resistance between terminal 21 of J 39700 and terminal A of the WSS harness connector. Is the resistance within the range specified in the value(s) column? | 0-5ohms | ||
11 | Repair CKT 873 for an open or high resistance. Refer to Wiring Repairs . If an open or high resistance is found in the jumper harness, replace the jumper harness. Refer to Wheel Speed Sensor Jumper Harness Replacement . Is the repair complete? | -- | -- | |
12 | Malfunction is intermittent. Inspect all connectors and harnesses for damage that may result in an open or high resistance when connected. Refer to Wiring Repairs . Is the repair complete? | -- | -- | |
Is the voltage within the range specified in the value(s) column? | Above 1V | |||
14 | Repair CKT 830 for a short to voltage. Refer to Wiring Repairs . If a short to voltage is found in the jumper harness, replace the jumper harness. Refer to Wheel Speed Sensor Jumper Harness Replacement . Is the repair complete? | -- | -- | |
Using J 39200 DMM, measure the voltage at terminal 21 of J 39700 . Is the voltage within the range specified in the value(s) column? | Above 1V | |||
16 | Repair CKT 873 for a short to voltage. Refer to Wiring Repairs . If a short to voltage is found in the jumper harness, replace the jumper harness. Refer to Wheel Speed Sensor Jumper Harness Replacement . Is the repair complete? | -- | -- | |
17 | Replace the EBCM. Refer to Electronic Brake Control Module Replacement . Is the replacement complete? | -- | -- | |
18 |
Does the DTC reset as a current DTC? | -- |
