- Remove the
J 42168-9 (1) and thumbscrew from the
J 42168-1 (2).
- Remove the
J 42168-1 from the left bearing cup bore of the differential housing.
Note: Level the tool in order to obtain accurate measurements.
- Install the
DT-48009-2 into a vice.
- Position the bearing cup (2) onto the
DT-48009-2 (3).
- Use the
J 42155 in order to position the differential case (1) onto the
DT-48009-2 (3) and into the bearing cup (2). Rotate the differential, in both
directions, in order to seat the bearing to the cup.
- Install the
DT-48009-3 (2) into the hole in
J 42168-2 (1). Loosen the thumbscrew and allow the rod to contact the bottom of the bearing cup
bore, machined surface (3).
- Tighten the thumbscrew.
- Remove the
DT-48009-3 from the
J 42168-2 (1).
- Using a ring gear bolt, attach the
DT-48009-3 (2) to the ring gear side of the differential (1).
- Rotate the differential until the rod of
DT-48009-3 (2) is above the
DT-48009-2 (3) gage block.
- The
DT-48009-2 upper gage block location (1) is used when servicing 2.56, 2.73, and 2.93 ratio differentials.
- Using a feeler gage, measure the distance between the rod of
DT-48009-3 (1) and the gage block of
DT-48009-2 (2). Record the measurement
as dimension C1.
- Subtract C1 value from a C nominal value of 5 mm (0.197 in). Record that calculation as C2.
Refer to the applicable calculation table in
Spacer and Shim Specifications.
- Locate the A2 value (2) on the side of the ring gear.
Note: The A2 value is a manufacturing variation between the ring gear and pinion. The A2 value may be higher, lower, or equal to 74.5 mm (2.93 in), 2.93 ratio differential, nominal value. When subtracting the D nominal
value from the A2 value, the C3 calculation may compute to a positive, negative, or zero total.
- Subtract the D nominal value of 74.5 mm (2.93 in) from the A2 value. Record the calculation as C3.
- Add the C2 value to the C3 value for the proper left side differential bearing shim thickness. The C3 value may be a positive, negative, or zero value.
- Select shims equal to the calculated value. It may be necessary to round the shim or shims total to obtain the proper shim sizes. If the shim thickness calculation is past the midpoint value, round the number to the next decimal
value. Refer to
Rear Axle Specifications.
- Remove the pinion housing/cage bolts (1).
- Remove the pinion housing/cage (4) from the differential.
- Remove the
J 42168-11 , bearings (3 and 6), spacer (5), and the
J 42168-2 (7) from the pinion housing/cage (4).
Caution: Use the DT-48008 to support the differential housing in the press to prevent damage to the differential housing.
- Use the
DT-48008 (4), the
J 42170 (1) and a hydraulic press in order to install the selected shim (3) and bearing cup (2)
to the differential housing.
- Install the differential assembly (1) onto the
J-42173-A (2).
Caution: Refer to Fastener Caution in the Preface section.
- Install 4 M8 x 1.25 bolts (3) and tighten to
28 N·m (20 lb ft).
- Install the ring gear (1) to the differential. Use several bolts to properly align the ring gear to the case.
A hammer and brass punch may be used to aid in seating the ring gear onto the differential case.
Note: Two types of ring gear bolts may be available for replacement. First design bolts (3) have serrations under the head and are torqued to 195 N·m (144 lb ft). The second design (4) are smooth
under the head and are torqued to 145 N·m (107 lb ft).
- Install the NEW ring gear bolts (2).
- Position the differential assembly onto the
J-42173-A .
| • | Tighten the ring gear bolts to
195 N·m (144 lb ft) - 1st design. |
| • | Tighten the ring gear bolts to
145 N·m (107 lb ft) - 2nd design. |
- Use the
J 42155 in order to install the differential case into the differential housing.
- Install the right side bearing cup (104), and the
J 42168-15 onto the differential.
Note: In order to perform the shim selection procedure:
| • | The oil seal must be removed from the right cover. |
| • | The pinion housing/cage must NOT be installed to the differential case. |
- Install the right cover (3) and
J 42168-16 bolts (1) and spacers (2) to the differential. Position the
J 42168-16 bolts and spacers evenly apart and tighten
to
28 N·m (20 lb ft).
- Insert a feeler gage into the
J 42168-15 and measure the gap. The measured dimension is the right side differential bearing shim size.
- Remove the bolts (1), cover (3), and tools.
- Install the selected shim (103) and bearing cup (104) to the right cover.
- Using the
J 42170 and a hydraulic press, install the shim or shims and bearing cup into the right cover. Refer to
Rear Axle Assemble.
