GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2004 🢒 XLR 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 DTC P2122

Circuit Description

The accelerator pedal position (APP) sensors 1 and 2 are located within the accelerator pedal assembly. Each sensor has the following circuits:

    •  A 5-volt reference circuit
    •  A low reference circuit
    •  A signal circuit

This provides the engine control module (ECM) with a signal voltage proportional to accelerator pedal movement. The APP sensor 1 signal voltage at the rest position is near the low reference and increases as the pedal is actuated.If the ECM detects that the signal voltage is less than 0.1465 volts, DTC P2122 will set.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

The APP sensor 1 voltage is less than 0.1465 volt for more than 300 milliseconds.

Action Taken When the DTC Sets
    • The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records.
    • The control module commands the TAC system to operate in the Reduced Engine Power mode.
    • A message center or an indicator displays Reduced Engine Power.
    • Under certain conditions the control module commands the engine OFF.

Conditions for Clearing the MIL/DTC
    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check--Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2
  1. Turn ON the ignition, with the engine OFF.
  2. Observe the accelerator pedal position (APP) sensor 1 parameter with a scan tool.

Is the APP sensor 1 voltage less than the specified value?

0.15 V

Go to Step 5

Go to Step 3

3
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records

Does the DTC fail this ignition?

--

Go to Step 5

Go to Step 4

4
  1. Clear the DTCs with a scan tool.
  2. Slowly depress the accelerator pedal to wide open throttle (WOT), then slowly return the accelerator pedal to the closed position.
  3. Repeat this action several times.

Did the DTC fail this ignition?

--

Go to Step 14

Intermittent Conditions

5
  1. Turn OFF the ignition.
  2. Disconnect the APP sensor harness connector.
  3. Turn ON the ignition, with the engine OFF.
  4. Measure the voltage from the 5-volt reference circuit of the APP sensor 1 to a good ground with a DMM.

Is the voltage within the specified range?

4.8-5.2 V

Go to Step 6

Go to Step 7

6
  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the APP sensor 1 and the signal circuit of the APP sensor 1.
  3. Turn ON the ignition, with the engine OFF.
  4. Observe the APP sensor 1 parameter with a scan tool.

Is the APP sensor 1 voltage within the specified range?

4.8-5.2 V

Go to Step 11

Go to Step 9

7
  1. Measure the voltage from the 5-volt reference circuit of the throttle position (TP) sensor 1 to a good ground with a DMM.
  2. Disconnect all components that share the 5-volt reference voltage source one at a time.

Is the voltage within the specified range after disconnecting any component?

4.8-5.2 V

Go to Step 13

Go to Step 8

8
  1. Test the 5-volt reference circuit of the APP sensor 1 for the following conditions:
    2. • A short to ground
    • High resistance
    • An open circuit
  2. Repair as necessary. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 16

Go to Step 10

9
  1. Test the signal circuit of the APP sensor 1 for the following conditions:
    2. • A short to ground
    • A short to the low reference circuit
    • High resistance
    • An open circuit
  2. Repair as necessary. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 16

Go to Step 12

10
  1. Test the 5-volt reference circuits of the manifold absolute pressure (MAP) sensor for a short to ground.
  2. Repair as necessary. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 16

Go to Step 12

11

Test for an intermittent and for a poor connection at the APP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 16

Go to Step 14

12

Test for an intermittent and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 16

Go to Step 15

13

Replace the component that, when disconnected, caused the voltage to return to the specified value. Refer to the appropriate replacement procedure.

Did you complete the replacement?

--

Go to Step 16

--

14

Replace the accelerator pedal assembly. Refer to Accelerator Pedal Position Sensor Replacement .

Did you complete the replacement?

--

Go to Step 16

--

15

Replace the ECM. Refer to Engine Control Module Replacement .

Did you complete the replacement?

--

Go to Step 16

--

16
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 17

17

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

System OK