Circuit Description
The engine control module (ECM) provides 12 volts to the park/neutral switch of the manual shift shaft position switch. The manual shift shaft position switch is a sliding contact assembly that attaches to the manual shift shaft inside the transmission. The switch consists of five separate circuits, four of which indicate gear selector position to the transmission control module (TCM), and one that indicates park/neutral position to the ECM. When the transmission is in PARK or NEUTRAL, the switch closes and pulls the ECM voltage low, 0 volts. When the transmission is not in PARK or NEUTRAL, the ECM voltage is high, 12 volts. The ECM uses the switch in order to enable starter operation.
If the park/neutral switch and the transmission manual shift shaft position switch do not agree for a specified length of time, DTC P0850 sets. DTC P0850 is a type C DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0850 Park/Neutral Position (PNP) Switch Circuit
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
DTC P0850 sets when either of the following conditions are true:
Condition 1
The park/neutral switch circuit is low, 0 volts, for 100 seconds while the TCM is reporting the gear selector is in REVERSE or any forward range.
Condition 2
The park/neutral switch circuit is high, 12 volts, for 200 seconds while the TCM is reporting the gear selector is in PARK or NEUTRAL.
Action Taken When the DTC Sets
| • | The ECM does not illuminate the malfunction indicator lamp (MIL). |
| • | The ECM uses the transmission range data to enable engine cranking. |
| • | The ECM stores the operating conditions when the Conditions for Setting the DTC are met. This information is stored as a Failure Record. |
| • | The ECM stores DTC P0850 in ECM history. |
Conditions for Clearing the MIL/DTC
| • | The ECM clears the DTC from ECM history if the vehicle completes 40 warm-up cycles without a non emission diagnostic fault occurring. |
| • | The ECM cancels the default action when the ignition is OFF long enough in order to power down the ECM. |
| • | A scan tool can clear the DTC. |
Step | Action | Value(s) | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |||||
2 |
Important::
| -- | Go to Step 3 | |||||
3 |
Does the PNP Switch display Park/Neutral? | -- | Go to Step 4 | Go to Step 8 | ||||
4 | Shift the transmission from PARK to DRIVE. Does the PNP Switch display "In Gear"? | -- | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 5 | ||||
5 | Disconnect the automatic transmission inline 20-way connector. Does the PNP Switch display Park/Neutral? | -- | Go to Step 6 | Go to Step 7 | ||||
6 | Test the PNP Switch signal circuit for a short to ground between the automatic transmission inline 20-way connector and manual shift shaft position switch. Refer to Testing for Short to Ground . Did you find the condition? | -- | Go to Step 11 | Go to Step 12 | ||||
7 | Test the park/neutral signal circuit for a short to ground between the automatic transmission inline 20-way connector and the ECM. Refer to Testing for Short to Ground . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 13 | ||||
8 |
Does the PNP Switch display Park/Neutral? | -- | Go to Step 10 | Go to Step 9 | ||||
9 | Test the park/neutral signal circuit for an open between the automatic transmission inline 20-way connector and the ECM. Refer to Testing for Continuity and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 13 | ||||
10 | Test the park/neutral signal circuit for an open between the automatic transmission inline 20-way connector and the manual shift shaft position switch. Refer to Testing for Continuity . Did you find the condition? | -- | Go to Step 11 | Go to Step 12 | ||||
11 | Replace the transmission internal wiring harness. Refer to Transmission Internal Electrical Harness Replacement . Is the action complete? | -- | Go to Step 14 | -- | ||||
12 | Replace the manual shaft shift position switch. Refer to Manual Shift Shaft Position Switch Replacement . Is the action complete? | -- | Go to Step 14 | -- | ||||
13 | Replace the ECM. Refer to Control Module References for replacement, setup and programming. Is the action complete? | -- | Go to Step 14 | -- | ||||
14 | Perform the following procedure to verify the repair:
Has the test run and passed? | -- | Go to Step 15 | Go to Step 2 | ||||
15 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK |
