GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2006 🢒 SRX 🢒 Accessories 🢒 Navigation Systems 🢒 DTC C0192

Circuit Description

The longitudinal accelerometer is used to determine straight-line acceleration. This information is used when calculating the desired Traction Control in AWD applications.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC C0192 All Wheel Drive (AWD)/Four Wheel Drive (4WD) Reference Accelerometer Circuit Range/Performance

Conditions for Running the DTC
    • The ignition is ON.
    • Ignition voltage is greater than 8 volts.

Conditions for Setting the DTC

One of the following conditions exist:

    • The longitudinal accelerometer sensor input voltage is less than 0.15 volt.
    • The longitudinal accelerometer sensor input voltage is greater than 4.85 volts for 1 second.
    • The longitudinal accelerometer bias exceeds 0.5 g.
    • The longitudinal accelerometer signal is not increased by 0.5 volt during longitudinal accelerometer self test.

Action Taken When the DTC Sets
    • TCS is degraded.
    • The TCS indicators turn ON.
    • The ABS remains funtional.

Conditions for Clearing the DTC
    • The condition for the DTC is no longer present and the DTC is cleared with a scan tool.
    • The electronic brake control module (EBCM) automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.

Diagnostic Aids

Thoroughly inspect connections and wiring that may cause an intermittent malfunction. Refer to Testing for Electrical Intermittents , Testing for Intermittent Conditions and Poor Connections , Wiring Repairs , and Connector Repairs .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests for the proper voltage output on the 5-volt reference circuit and the proper operation of the signal circuit.

    2.

  2. This step tests for possible low 5-volt reference output or a problem with the signal circuit.

    3.

  3. This step tests for a short to voltage on the 5-volt reference circuit. If a short to voltage exists, other DTCs may be set for the vehicle stability system if equipped.

    4.

  4. This step tests for a problem with the low reference circuit. If a short to voltage exists, other DTCs may be set for the vehicle stability system if equipped.

Step

Action

Values

Yes

No

Schematic Reference: Antilock Brake System Schematics

Connector End View Reference: Antilock Brake System Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the longitudinal accelerometer 5-volt reference circuit and the longitudinal accelerometer signal circuit.
  3. Turn ON the ignition, with the engine OFF.
  4. With the scan tool, observe the longitudinal accelerometer parameter.

Does the scan tool indicate that the longitudinal accelerometer parameter is in between the specified voltage range?

4.5-5.5 V

Go to Step 8

Go to Step 3

3

With the 3-amp fused jumper wire still connected, does the scan tool indicate that the longitudinal accelerometer parameter is in below the specified voltage value?

4.5 V

Go to Step 5

Go to Step 4

4

Test the longitudinal accelerometer 5-volt reference circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 12

Go to Step 7

5

Test the longitudinal accelerometer 5-volt reference circuit for the following conditions:

    • An open
    • A short to ground
    • A high resistance

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 12

Go to Step 6

6

Test the longitudinal accelerometer signal circuit for the following conditions:

    • An open
    • A short to ground
    • A high resistance

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 12

Go to Step 11

7

Test the longitudinal accelerometer signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 12

Go to Step 11

8

Test the longitudinal accelerometer low reference circuit for the following conditions:

    • An open
    • A short to voltage
    • A high resistance

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

9

Inspect for poor connections at the harness connector of the yaw rate and lateral accelerometer sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 12

Go to Step 10

10

Replace the yaw rate and lateral accelerometer sensor. Refer to Brake Pressure Modulator Valve Pressure Sensor Replacement .

Did you complete the replacement?

--

Go to Step 12

--

11

Replace the electronic brake control module (EBCM). Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 12

--

12
  1. Clear the DTCs using the scan tool.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK