Step | Action | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Adjustable Pedal Schematics Connector End View Reference: Adjustable Pedal Connector End Views | |||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||
2 | Verify the fault is present. Does the system operate normally? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | ||||||
3 |
Does the scan tool display the correct switch status in relation to the actual switch position? | Go to Step 7 | Go to Step 4 | ||||||
4 |
Does the test lamp illuminate? | Go to Step 5 | Go to Step 10 | ||||||
5 | Connect a fused jumper wire from the battery voltage supply circuit terminal to the adjustable pedal forward switch signal circuit terminal in the switch harness connector. Does the scan tool display the adjustable pedal forward switch as active? | Go to Step 6 | Go to Step 8 | ||||||
6 | Connect a fused jumper wire from the battery voltage supply circuit terminal to the adjustable pedal rearward switch signal circuit terminal in the switch harness connector. Does the scan tool display the adjustable pedal rearward switch as active? | Go to Step 12 | Go to Step 8 | ||||||
7 |
Important: If the pedals are at one of the stops the memory seat module will not attempt to activate the motor in that direction. Does the test lamp illuminate while the switch is in the forward and rearward directions? | Go to Step 11 | Go to Step 9 | ||||||
8 | Test the adjustable pedal switch signal circuit for an open or short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 14 | ||||||
9 | Test the adjustable pedal motor control circuits to the memory seat module for an open or short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 14 | ||||||
10 | Repair the battery voltage supply circuit to the adjustable pedal switch for an open or short to ground. Is the repair complete? | Go to Step 18 | -- | ||||||
11 | Test the motor control circuits in the I/P harness for the following conditions:
Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 13 | ||||||
12 | Inspect for poor connections at the adjustable pedal switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 15 | ||||||
13 | Inspect for poor connections at the adjustable pedal motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 16 | ||||||
14 | Inspect for poor connections at the memory seat module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 18 | Go to Step 17 | ||||||
15 | Replace the adjustable pedal switch. Is the repair complete? | Go to Step 18 | -- | ||||||
16 | Replace the adjustable pedal motor. Refer to Brake and Accelerator Pedal Adjuster Actuator Motor Replacement . Is the repair complete? | Go to Step 18 | -- | ||||||
17 | Replace the memory seat module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Is the repair complete? | Go to Step 18 | -- | ||||||
18 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 3 | ||||||
