Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B1735 01: Seat Front Up Switch Circuit Short to BatteryDTC B1740 01: Seat Front Down Switch Circuit Short to Battery
DTC B1745 01: Seat Rear Up Switch Circuit Short to Battery
DTC B1750 01: Seat Rear Down Switch Circuit Short to Battery
DTC B1755 01: Seat Assembly Forward Switch Circuit Short to Battery
DTC B1760 01: Seat Assembly Rearward Switch Circuit Short to Battery
DTC B1815 01: Seat Recline Forward Switch Circuit Short to Battery
DTC B1820 01: Seat Recline Rearward Switch Circuit Short to Battery
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Front Vertical Up Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Front Vertical Down Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Rear Vertical Up Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Rear Vertical Down Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Horizontal Forward Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Horizontal Rearward Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Recline Forward Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
Recline Rearward Switch Signal | 2 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01 | -- |
1. Power seat is inoperative 2. Scan Tool Does Not Communicate with Low Speed GMLAN Device | ||||
Circuit Description
When the power seat switches are pressed, they send a 12-volt signal through the switch signal circuits to the memory seat module (MSM). The MSM then commands the driver seat motors to move in response to the switch signals.
Conditions for Running the DTC
The MSM must be powered.
Conditions for Setting the DTC
| • | If a seat switch circuit is active in one direction and the switch for the opposite direction is pressed, this DTC will set. |
| • | A short to voltage on a switch signal circuit. |
Action Taken When the DTC Sets
| • | A motor output driven in response to a switch considered failed, is deactivated for both directions. |
| • | All memory recall commands are ignored. |
| • | The MSM will respond to any other switch signal that has not set a DTC. |
Conditions for Clearing the DTC
| • | The current DTC will clear and set the code to history, 3 seconds after the fault is no longer present and the power mode changes to OFF then back to ACC or RUN. |
| • | The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Diagnostic Aids
| • | The scan tool may reference the Memory Seat Module as the Driver Position Module. |
| • | If one of the switch signal circuits is shorted to battery, multiple codes will set. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Memory Seats Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, observe the scan tool Driver Position Module seat switch parameters, while pressing the seat directional switches. The reading should change between Inactive and Active.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the seat adjuster switch.
- Ignition ON, verify the scan tool seat switch parameters listed below are Inactive:
- If all circuits test normal, test or replace the seat adjuster switch.
| • | Front Vertical Upward Switch |
| • | Front Vertical Downward Switch |
| • | Rear Vertical Upward Switch |
| • | Rear Vertical Downward Switch |
| • | Horizontal Forward Switch |
| • | Horizontal Rearward Switch |
| • | Recline Forward Switch |
| • | Recline Rearward Switch |
| ⇒ | If not the specified value, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace the MSM. |
| • | Front vertical up switch terminal A |
| • | Front vertical down switch terminal K |
| • | Rear vertical up switch terminal F |
| • | Rear vertical down switch terminal J |
| • | Horizontal forward switch terminal D |
| • | Horizontal rearward switch terminal C |
| • | Recline forward switch terminal H |
| • | Recline rearward switch terminal G |
Component Testing
- Ignition OFF, disconnect the harness connector at the seat adjuster switch.
- Test for infinite resistance between each seat direction signal terminal listed below and the B+ terminal E with the switch in the open position.
- Test for less than 1 ohm between each seat direction signal terminal listed below and the B+ terminal E with the switch in the closed position.
| • | Front vertical up switch terminal A |
| • | Front vertical down switch terminal K |
| • | Rear vertical up switch terminal F |
| • | Rear vertical down switch terminal J |
| • | Horizontal forward switch terminal D |
| • | Horizontal rearward switch terminal C |
| • | Recline forward switch terminal H |
| • | Recline rearward switch terminal G |
| ⇒ | If less than the specified value, replace the adjuster switch. |
| • | Front vertical up switch terminal A |
| • | Front vertical down switch terminal K |
| • | Rear vertical up switch terminal F |
| • | Rear vertical down switch terminal J |
| • | Horizontal forward switch terminal D |
| • | Horizontal rearward switch terminal C |
| • | Recline forward switch terminal H |
| • | Recline rearward switch terminal G |
| ⇒ | If greater than the specified range, replace the adjuster switch switch. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for MSM replacement, setup, and programming |
