Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B0283 05: Electric Rear Defrost Circuit Short to Battery or OpenDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Relay Switch B+ | 2 | 2 | -- | -- |
Rear Defog Relay Control | 2 | B0283 05 | B0283 05 | -- |
Rear Defogger Grid Control | 2 | 2 | 1 | -- |
Relay Coil Ground | -- | B0283 05 | 2 | -- |
Rear Window Defogger Grid Ground | -- | 2 | 2 | -- |
1. Rear Defogger Always ON 2. Rear Defogger Inoperative | ||||
Circuit/System Description
The HVAC control module monitors the voltage level on the supply voltage circuit of the rear defog relay. The voltage level should be low while the rear defog relay is de-energized. The voltage will be near system voltage when the HVAC control module energizes the rear defog relay.
Conditions for Running the DTC
Battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
The HVAC control module detects a short to battery or open/high resistance in the defog relay coil control circuit for 1 second or greater.
Action Taken When the DTC Sets
The rear window defogger will not operate.
Conditions for Clearing the DTC
| • | The DTC clears when the fault is no longer detected. |
| • | The current DTC will become history when the request for the output is removed. |
| • | The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Rear Window Defogger Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Command the Rear Defog Request ON and OFF with the scan tool. The rear window defogger should turn ON and OFF when changing between the commanded states.
Circuit/System Testing
- Ignition OFF, disconnect the RR DEFOG relay.
- Test for less than 1 ohm between the relay coil ground circuit terminal and ground.
- Connect a test lamp between the relay control circuit terminal and the relay coil ground circuit terminal.
- Ignition ON, command the Rear Defog Request ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, test or replace the RR DEFOG relay.
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the HVAC control module. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the HVAC control module. |
Component Testing
Relay Test
- Ignition OFF, disconnect the RR DEFOG relay.
- Test for 60-180 ohms between terminals 85 and 86.
- Test for infinite resistance between the following terminals:
- Install a 25-amp fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms between terminals 30 and 87.
| ⇒ | If not within the specified range, replace the relay. |
| • | 30 and 86 |
| • | 30 and 87 |
| • | 30 and 85 |
| • | 85 and 87 |
| ⇒ | If not the specified value, replace the relay. |
| ⇒ | If greater than the specified range, replace the relay. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for HVAC control module replacement, setup, and programming |
