The TV antenna signal circuits consists of 4 individual coaxial cables that carries the TV signal information received by the TV antenna through the TV antenna amplifier and then to the TV antenna module.

This test is run every 300 milliseconds.

The TV antenna module detects a open or short to ground on one or more of the 4 TV antenna coax cables for 20 seconds.

The TV antenna module disables all 4 coax cables when a short to ground is detected in one or more of the TV antenna inputs. When the TV antenna detects an open in one or more TV antenna coax inputs the remainder of the 4 unaffected TV antenna coax inputs continue to operate.

Schematic Reference

Video System Schematics

Connector End View Reference

Entertainment Connector End Views

Description and Operation

Navigation System Description and Operation

Electrical Information Reference

1. With the TV function OFF, disconnect the 4 TV coaxial cables at the TV antenna amplifier.
2. With the TV function ON wait 20 seconds, Verify each of the 4 TV coax cable center conductors have greater than 1 volt.

⇒	If 1TV coaxial cable center connector is less than 1 volt, replace the suspect TV antenna coaxial cable.

⇒	If all 4 TV coaxial cable center connectors are less than 1 volt, see Component Testing (Coaxial Cables - TV Antenna Module to TV Antenna Amplifier).

3. With the TV function OFF, reconnect the 4 TV coaxial cables to the TV antenna amplifier.
4. Disconnect the 4 TV coaxial cables at the TV antenna.
5. With the TV function ON wait 20 seconds, Verify each of the 4 TV coax cable center conductors have greater than 1 volt.

⇒	If all 4 TV coaxial cable center connectors are less than 1 volt, see Component Testing (Coaxial Cables - TV Antenna Amplifier toTV Antenna).

⇒	If all 4 TV coaxial cable center connectors are greater than 1 volt replace the rear glass (TV antenna).

⇒	If 1TV coaxial cable center connector is less than 1 volt, replace the suspect TV antenna coaxial cable.

Important: Perform the Circuit/System Testing before using this diagnostic.

1. Ignition Off. Disconnect the 4 TV coaxial cables from the TV antenna module and the TV antenna amplifier. Test the resistance of each TV antenna coaxial cable center conductor from end to end. Verify the resistance is less than 5 ohms.

⇒	If the resistance is greater than 5 ohms, replace the suspect TV antenna coaxial cable.

2. Test the resistance of all 4 TV antenna coaxial cables outer shields from end to end. Verify the resistance is less than 5 ohms.

⇒	If the resistance is greater than 5 ohms , replace the suspect TV antenna coaxial cable.

3. Test the resistance of all 4 TV antenna coaxial cables between the center conductor and the outer conductor. Verify there is infinite resistance between both conductors.

⇒	If there is less than infinite resistance between the inner conductor and the outer conductor of the coaxial cable, replace the suspect TV antenna coaxial cable. If the coaxial cable tests normal, replace the TV antenna module.

Important: Perform the Circuit/System Testing before using this diagnostic.

1. Ignition Off. Disconnect the 4 TV coaxial cables from the TV antenna amplifier and the TV antenna.
2. Test the resistance of each TV antenna coaxial cable center conductor from end to end. Verify the resistance is less than 5 ohms.

⇒	If the resistance is greater than 5 ohms, replace the suspect TV antenna coaxial cable.

3. Test the resistance of all 4 TV antenna coaxial cables outer shields from end to end. Verify the resistance is less than 5 ohms.

⇒	If the resistance is greater than 5 ohms , replace the suspect TV antenna coaxial cable.

4. Test the resistance of all 4 TV antenna coaxial cables between the center conductor and the outer conductor. Verify there is infinite resistance between both conductors.

⇒	If there is less than infinite resistance between the inner conductor and the outer conductor of the coaxial cable, replace the suspect TV antenna coaxial cable. If the coaxial cable tests normal, replace the TV antenna amplifier.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.