GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2006 🢒 CTS 🢒 DTC 🢒 DTC P0608

Circuit Description

The engine control module (ECM)/powertrain control module (PCM) creates the vehicle speed output signal by pulsing the circuit to ground. The ECM/PCM monitors the voltage on the vehicle speed output circuit. If the ECM/PCM determines that the voltage is out of the normal operating range, a DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0608 Vehicle Speed Output Circuit

Conditions for Running the DTC
    • The engine speed is more than 400 RPM.
    • The ignition voltage is between 6-18 volts.

Conditions for Setting the DTC
    • The ECM/PCM detects that the commanded state of the driver and the actual state of the signal circuit do not match.
    • The above condition must be present for a minimum of 5 seconds.

Action Taken When the DTC Sets

The ECM/PCM records the operating conditions at the time the diagnostic fails. The ECM/PCM displays the failure information in the Failure Records on the scan tool.

Conditions for Clearing the MIL/DTC
    • The history DTC clears after 40 malfunction-free warm-up cycles.
    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The ECM/PCM receives the clear code command from the scan tool.

Step

Action

Yes

No

Schematic Reference: Instrument Cluster Schematics

Connector End View Reference: Engine Control Module Connector End Views for the 2.8L engine, Engine Control Module Connector End Views for the 3.6L engine, or Engine Control Module Connector End Views for the 6.0L engine

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2
  1. Install a scan tool.
  2. Disconnect the radio.
  3. Raise the vehicles drive wheels. Refer to Lifting and Jacking the Vehicle .
  4. Start the engine.
  5. Place the transmission into drive for an automatic transmission or third gear for a manual transmission.
  6. With the scan tool, observe the Vehicle Speed Sensor parameter in the engine control module (ECM)/powertrain control module (PCM) Engine Data 1 data list.

Does the Vehicle Speed Sensor parameter match the speedometer display?

Go to Step 10

Go to Step 3

3
  1. Turn OFF the ignition.
  2. Disconnect the ECM/PCM connector C2.
  3. Turn ON the ignition, with the engine OFF.
  4. Measure the voltage from the vehicle speed signal circuit to a good ground.

Does the voltage measure greater than 9 volts?

Go to Step 4

Go to Step 5

4

Test the vehicle speed signal circuit for a short to battery voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 11

Go to Step 6

5

Test the vehicle speed signal circuit for the following:

    • An open
    • Short to ground
    • A high resistance

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 11

Go to Step 7

6

Inspect for poor connections at harness connector of the ECM/PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 11

Go to Step 8

7

Inspect for poor connections at the harness connector of the instrument panel cluster (IPC). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 11

Go to Step 9

8

Replace the ECM/PCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 11

--

9

Replace the IPC. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 11

--

10

Replace the radio. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 11

--

11
  1. Use the scan tool in order to clear the DTCs.
  2. Operate vehicle within the Conditions for Running this DTC.

Does the DTC reset?

Go to Step 2

System OK