SMU - SECTION 10-6 - REVISED REMOVE/INSTALL PROC. FOR DOOR. Buick Skylark 1996

REVISION: 02/14/96

THIS BULLETIN IS BEING REVISED TO UPDATE STEP 8 IN THE "REMOVE OR DISCONNECT" PROCEDURE. PLEASE DISCARD CORPORATE BULLETIN NUMBER 53-10-29 (SECTION 10 - BODY). **********************************************************************

SUBJECT: SERVICE MANUAL UPDATE - SECTION 10-6 - REVISED REMOVE/ INSTALL PROCEDURE FOR DOOR TRIM PANEL

MODELS: 1996 BUICK SKYLARK 1996 OLDSMOBILE ACHIEVA 1996 PONTIAC GRAND AM

THIS BULLETIN REVISES THE REMOVAL AND INSTALLATION PROCEDURE FOR THE DOOR TRIM PANEL. PLEASE ADD THIS PROCEDURE TO SECTION 10-6 OF THE SERVICE MANUAL.

DOOR TRIM PANEL -

FIGURES 9 - 14 (REFER TO SECTION 10-6 OF THE SERVICE MANUAL)

REMOVE OR DISCONNECT -

1. FRONT DOOR UPPER TRIM PANEL BY GENTLY PRYING AT SIDE TO DISENGAGE TABS AND PULL REARWARD.

2. BUICK & OLDSMOBILE - FRONT LEFT DOOR POWER LOCK AND WINDOW SWITCH BEZEL BY ENGAGING A SMALL FLAT BLADE SCREWDRIVER TO SPRING CLIP UNDER REAR OF BEZEL.

3. BUICK - REAR DOOR POWER WINDOW SWITCH BY PRYING UNDER BEZEL.

4. PONTIAC - FRONT/REAR POWER DOOR POWER LOCK/WINDOW SWITCH BEZEL BY PRYING UNDER REAR EDGE OF THE BEZEL AFTER TWO SCREWS ARE REMOVED.

5. BUICK & OLDSMOBILE - POWER DOOR LOCK SWITCH.

6. WIRE HARNESS CONNECTORS.

7. MANUAL LOCK SLIDER KNOB BY PULLING OUTWARD TO DISENGAGE FROM LOCKING ROD.

8. PONTIAC - DOOR INSIDE HANDLE ESCUTCHEON BY PULLING INSIDE DOOR HANDLE TO OPEN POSITION AND GENTLY DISENGAGE BY PULLING FRONT OF ESCUTCHEON OUTWARD.

9. BUICK & OLDSMOBILE - DOOR INSIDE HANDLE ESCUTCHEON BY ROTATING AND PULLING FORWARD TO SLIDE OVER DOOR HANDLE.

10. REFLECTOR USING A FLAT BLADE SCREWDRIVER.

11. PONTIAC - FRONT OR REAR DOOR TRIM PANEL SCREW BEHIND REFLECTOR AND PULL CUP.

12. BUICK & OLDSMOBILE - FRONT OR REAR DOOR TRIM PANEL SCREWS, BEHIND REFLECTOR, UNDER ARMREST AND BEHIND DOOR INSIDE ESCUTCHEON.

13. WINDOW REGULATOR HANDLE, IF APPLICABLE - REFER TO "WINDOW REGULATOR HANDLE" IN THIS SECTION.

14. DOOR TRIM PANEL RETAINERS USING J38778 - TRIM REMOVAL TOOL. START AT THE BOTTOM AND GENTLY PRY INWARD SEPARATING TRIM FROM INNER, THEREBY DISENGAGING ALL RETAINERS FROM DOOR INNER.

15. DOOR TRIM PANEL BY LIFTING AT PULL HANDLE AND APPLYING PRESSURE IN THE OUTBOARD DIRECTION JUST BENEATH THE BELTLINE. BELTLINE PRESSURE EXERTED AT THE UPPER FRONT AND WORKING REARWARD WILL DISENGAGE TRIM PANEL BELTLINE HOOKS FROM DOOR INNER BELTLINE SLOTS.

16. DISENGAGE MIRROR SWITCH FROM BEZEL BY PUSHING ON THE SIDE OF MIRROR SWITCH.

INSTALL OR CONNECT -

1. ALIGN KEYWAY ON MIRROR SWITCH TO BEZEL, THEN GRASP MIRROR SWITCH HANDLE AND PULL TOWARDS BEZEL UNTIL IT SNAPS IN PLACE.

2. DOOR TRIM PANEL BY FIRST ALIGNING LOCATOR PINS ON BACK OF TRIM TO DOOR INNER. PUSH TRIM PANEL CLOSE BUT JUST SHORT OF FULL ENGAGEMENT. SET UPPER BELTLINE HOOKS BY APPLYING DOWNWARD PRESSURE AT TRIM PANEL BELTLINE.

3. ALIGN FASTENERS TO DOOR INNER PANEL RETAINER HOLES AND ENGAGE FASTENERS BY APPLYING PRESSURE TO DOOR TRIM PANEL.

4. WINDOW REGULATOR HANDLE, IF APPLICABLE - REFER TO "WINDOW REGULATOR HANDLE" IN THIS SECTION.

5. PONTIAC - FRONT OR REAR DOOR TRIM PANEL SCREW BEHIND REFLECTOR AND PULL CUP.

6. BUICK & OLDSMOBILE - FRONT OR REAR DOOR TRIM PANEL SCREWS, BEHIND REFLECTOR, UNDER ARMREST AND BEHIND DOOR INSIDE ESCUTCHEON.

7. DOOR INSIDE HANDLE ESCUTCHEON BY INSERTING DOOR HANDLE IN DOOR HANDLE OPENING.

8. INSERT DOOR INSIDE HANDLE ESCUTCHEON CLIPS TO FRONT END OF DOOR TRIM PANEL OPENING AND APPLY PRESSURE TO SECURE.

9. REFLECTOR BY ALIGNING CLIPS TO THE SLOTS IN DOOR TRIM PANEL AND APPLY PRESSURE TO SECURE.

10. MANUAL LOCK SLIDER KNOB BY POSITIONING ONTO LOCKING ROD AND SLIDE REARWARD.

11. WIRE HARNESS CONNECTORS.

12. BUICK & OLDSMOBILE - FRONT DOOR POWER LOCK AND WINDOW SWITCH BEZEL.

13. BUICK - REAR DOOR POWER WINDOW SWITCH.

14. PONTIAC - FRONT DOOR POWER LOCK AND WINDOW SWITCH AND BEZEL.

15. PONTIAC - REAR DOOR POWER WINDOW SWITCH AND BEZEL.

16. BUICK & OLDSMOBILE - POWER DOOR LOCK SWITCH.

17. FRONT DOOR UPPER TRIM PANEL BY INSERTING TABS TO RETAINERS AND APPLY PRESSURE TO SECURE.

FIGURES: 00 ATTACHMENTS: 00

GENERAL MOTORS BULLETINS ARE INTENDED FOR USE BY PROFESSIONAL TECHNICIANS, NOT A "DO-IT-YOURSELFER". THEY ARE WRITTEN TO INFORM THOSE TECHNICIANS OF CONDITIONS THAT MAY OCCUR ON SOME VEHICLES, OR TO PROVIDE INFORMATION THAT COULD ASSIST IN THE PROPER SERVICE OF A VEHICLE. PROPERLY TRAINED TECHNICIANS HAVE THE EQUIPMENT, TOOLS, SAFETY INSTRUCTIONS AND KNOW-HOW TO DO A JOB PROPERLY AND SAFELY. IF A CONDITION IS DESCRIBED, DO NOT ASSUME THAT THE BULLETIN APPLIES TO YOUR VEHICLE, OR THAT YOUR VEHICLE WILL HAVE THAT CONDITION. SEE A GENERAL MOTORS DEALER SERVICING YOUR BRAND OF GENERAL MOTORS VEHICLE FOR INFORMATION ON WHETHER YOUR VEHICLE MAY BENEFIT FROM THE INFORMATION.