DTC P1653 Traction Control Delivered Torque Output Circuit. Buick Park Avenue 1996

For 1990-2009 cars only

Makes 🢒 Buick 🢒 1996 🢒 Park Avenue 🢒 Engine 🢒 Engine Controls - 3.8L 🢒 DTC P1653 Traction Control Delivered Torque Output Circuit

Engine Controls Components
Gen Control, Volts Lamp, Shift Select Switch, EBTCM Module
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The Electronic Brake and Traction Control Module (EBTCM) controls the PWM signal on the Desired Torque circuit while monitoring the wheel speed sensors to detect slippage. The PCM monitors the PWM signal and reduces engine torque as needed by retarding ignition timing, decreasing boost duty cycle, increasing air/fuel ratio, or, in severe cases, shutting OFF up to three fuel injectors. The PCM sends a PWM signal to the Electronic Brake and Traction Control Module (EBTCM) on the delivered torque circuit informing the EBTCM of response made to the desired torque signal. A problem with the delivered torque circuit should cause DTC P1653 and ABS/TCS DTC 76 to set and traction control to be disabled. Refer to ABS/TCS for further information.

Conditions for Setting the DTC

•	The ignition is ON.

•	An improper voltage level has been detected on ODM B output 3 (the traction control delivered torque output control circuit).

•	The above conditions present for at least 30 seconds.

Action Taken When the DTC Sets

•	The PCM will not illuminate the malfunction indicator lamp (MIL).

•	The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as Freeze Frame data.

Conditions for Clearing the MIL/DTC

•	A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.

•	The DTC can be cleared by using the scan tool Clear Info function.

Diagnostic Aids

Check for the following conditions:

•	Poor connection at the PCM. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection.

•	Damaged harness. Inspect the wiring harness for damage.

•

If the harness appears to be OK, disconnect the PCM, turn the ignition ON and observe a digital multimeter connected between the Traction Control Delivered Torque control circuit and ground at the PCM harness connector while moving connectors and wiring harnesses related to the EBTCM. A change in voltage will indicate the location of the malfunction.

Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.

Test Description

Number(s) below refer to the step number(s) on the Diagnostic Table.

Normally, ignition feed voltage should be present on the control circuit with the PCM disconnected and the ignition turned ON.

Checks for a shorted component or a short to B+ on the control circuit. Either condition would result in a measured current of over 500 milliamps. Also checks for a component that is going open while being operated, resulting in a measured current of 0 milliamps.

Checks for a short to voltage on the control circuit.

This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.

DTC P1653 -- TCS Delivered Torque Control Circuit

Step

Action

Value(s)

Yes

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

Go to Step 2

Go to the Powertrain On Board Diagnostic (OBD) System Check

Turn OFF the ignition switch.
Disconnect the PCM.
Turn ON the ignition switch.
Using a J 39200 Digital Multimeter, measure voltage between the delivered torque control circuit at the PCM harness connector and ground.

Is voltage near the specified value?

B+

Go to Step 3

Go to Step 6

Connect the digital multimeter to measure current between the delivered torque control circuit at the PCM harness connector and ground.
Monitor the current reading on the digital multimeter for at least 2 minutes.

Does the current reading remain between the specified values?

0.001-0.5 Amp

(1-500 mA)

Go to Step 11

Go to Step 4

Turn OFF the ignition switch.
Disconnect the EBTCM (leave the PCM disconnected).
Turn ON the ignition switch.
Using the digital multimeter, measure voltage between the delivered torque control circuit and ground.

Is voltage at the specified value?

0 V

Go to Step 10

Go to Step 5

Locate and repair short to voltage in the delivered torque control circuit. Refer to Repair Procedures in Electrical Diagnosis.

Is action complete?

Go to Step 16

Turn OFF the ignition switch.
Check the ignition feed fuse for the EBTCM.

Is the fuse blown?

Go to Step 7

Go to Step 8

Locate and repair short to ground in ignition feed circuit for the EBTCM. Refer to Fuse Block Details in Electrical Diagnosis.
Replace the fuse.

Is action complete?

Go to Step 16

Disconnect the EBTCM.
Turn ON the ignition switch.
Measure voltage between the ignition feed circuit for the EBTCM and ground.

Is voltage near the specified value?

B+

Go to Step 9

Go to Step 13

Check the delivered torque control circuit for an open or a short to ground.
If a problem is found, repair the delivered torque control circuit. Refer to Repair Procedures in Electrical Diagnosis.

Was a problem found?

Go to Step 16

Go to Step 10

Check for the following conditions:

•	The delivered torque control circuit for a poor connection at the PCM.

•	The delivered torque control circuit for a poor connection at the EBTCM.

•	The EBTCM ignition feed circuit for a poor connection at the EBTCM.

If a problem is found, replace terminal(s) as necessary. Refer to Repair Procedures in Electrical Diagnosis.

Was a problem found?

Go to Step 16

Go to Step 14

Turn OFF the ignition switch.
Reconnect the PCM.
Disconnect the EBTCM.
Turn ON the ignition switch.
Connect a test light between the delivered torque control circuit and the ignition feed circuit at the EBTCM harness connector.
Using the scan tool outputs test function, cycle the delivered torque output ON and OFF.

Does the test light flash ON and OFF?

Refer to Diagnostic Aids

Go to Step 12

Check the delivered torque control circuit for a poor connection at the PCM.
If a problem is found, replace terminal. Refer to Repair Procedures in Electrical Diagnosis.

Was a problem found?

Go to Step 16

Go to Step 15

Locate and repair open in ignition feed circuit to the EBTCM. Refer to Repair Procedures in Electrical Diagnosis.

Is action complete?

Go to Step 16

Replace the EBTCM. Refer to On-Vehicle Service in ABS/TCS.

Is action complete?

Go to Step 16

Replace the PCM.

Important:: The replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming .

Is action complete?

Go to Step 16

Review and record scan tool Fail Records data.
Clear DTCs.
Operate the vehicle within Fail Records conditions.
Using a scan tool, monitor Specific DTC info for DTC P1653 until the DTC P1653 test runs.

Does the scan tool indicate DTC P1653 failed this ignition?

Go to Step 2

System OK