Circuit Description
The Vehicle Speed Sensor (VSS) is a Permanent Magnet (PM) generator attached to the transmission case extension. The final drive assembly has a toothed wheel (VSS rotor). As the final drive assembly rotates, an AC voltage is induced and transmitted to the Powertrain Control Module (PCM).
The PCM converts this AC voltage into a digital signal. The PCM uses the vehicle speed to determine the shift timing, the TCC apply and release, and the gear ratio calculations. The VSS voltage will vary from 0.5 volts AC at 100 RPM to more than 100 volts AC at 8000 RPM. The VSS resistance value is between 1300 and 1950 ohms.
When the PCM detects a low vehicle speed with a high engine speed while in a drive range, then DTC P0502 sets. DTC P0502 is a type A DTC.
Conditions for Setting the DTC
| • | No MAP DTCs P0107 or P0108 |
| • | No TP DTCs P0122 or P0123 |
| • | The transmission is not in Park or Neutral. |
| • | The engine speed is more than 2900 RPM. |
| • | The throttle angle is more than 15%. |
| • | The MAP is 0-105 kPa (0-15 psi). |
| • | The engine torque is 55-200 N·m (40-150 lb ft.). |
| • | The output speed is less than 150 RPM for 2.5 seconds. |
Action Taken When the DTC Sets
| • | The transmission defaults to 3rd gear. |
| • | The PCM inhibits TCC operation. |
| • | The PCM illuminates the Malfunction Indicator Lamp (MIL). |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the MIL after three consecutive ignition cycles without a failure reported. |
| • | A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | Check for PRNDL DTC P0705. DTC P0705 affects transmission operation. This may set DTC P0502 falsely. |
| • | Check for Electromagnetic Interference (EMI) in circuits 400 and 401. EMI may be induced if the harness is routed along the spark plug wires. |
| • | Inspect the wiring for poor electrical connections at the PCM. Inspect the wiring at the TCC brake switch. Look for the following conditions: |
| - | A bent terminal |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Poor terminal tension |
| - | A chafed wire |
| - | A broken wire inside the insulation |
| • | When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. |
| • | Ensure that the VSS is securely tightened to the case extension. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step verifies that the PCM is receiving a signal from the vehicle speed sensor.
-
This step verifies that there are no opens in the circuitry from the vehicle speed sensor to the PCM connector.
-
This step performs a resistance test on the VSS circuits from the PCM connector.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. Notice: In order to avoid damage to the drive axles, support the lower control arms in the normal horizontal position. Do not run the vehicle in gear with the wheels hanging down at full travel. With drive wheels rotating, does transmission output speed increase when wheel speed increases? | -- | Go to Diagnostic Aids | ||
Is the measured voltage greater than the specified value? | 0.5 v | |||
4 | Use the scan tool to find the most current calibration ID. Refer to Service Bulletins. Does the ID number match? | -- | ||
5 | Update the PCM with the latest calibration. Refer to Powertrain Control Module Replacement/Programming , Section 6. Is the calibration update complete? | -- | -- | |
6 | Remove the VSS and connect an ohmmeter from terminal A to terminal B of the VSS. Is the measured resistance within the specified range? | 1300-1950ohms | ||
Does the ohmmeter display a value greater than the specified value? | 1950ohms | |||
8 |
Refer to Troubleshooting Procedures, Section 8. Did you find and correct a problem? | -- | -- | |
9 | Does the ohmmeter display a value less than the resistance specified? | 1300ohms | ||
10 |
Refer to Troubleshooting Procedures, Section 8. Did you find and correct a problem? | -- | -- | |
11 |
Refer to Troubleshooting Procedures, Section 8. Did you find and correct a problem? | -- | ||
12 | Replace the VSS. Refer to Vehicle Speed Sensor Replacement, in On-Vehicle Service. Is the replacement complete? | -- | -- | |
13 | Replace the PCM. Refer to Powertrain Control Module Replacement/Programming , Section 6. Is the replacement complete? | -- | -- | |
14 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
